Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Dear Nordic Experts, This one's a tough nut to crack:
The firmware is based on nRF5 SDK for Mesh 5.0.0 with nRF5 SDK 17.0.2 and Softdevice s132 7.3.0. It runs on a nRF52832...
I tryed to reduce the power consumption of my beacon (ble_app_beacone example from SDK) to have more battery live. To do this, I want to reduce the TX power. And also change...
I have to initialize a i2c multiplexer, for that I am sending the device address and register address to be written using the function:
nrf_drv_twi_tx(&m_twi, (0x70), tx_buf...
Hi,
I'm currently using nRF Connect SDK v1.9.0 and developing on a nRF52832 onto a custom board. I'm using a BMI090L from Bosch connected over i2c.
I'm trying to suspend...
Hi.
Encountering an intermittent issue where, after a DFU (either OTA using Nordic Device Manager or over usb serial using dfu-util on Linux), the image is reportedly in...
In the DTS file for I2C, how do you set the port of the pin specified?
&i2c0 { compatible = "nordic,nrf-twi"; status = "okay"; sda-pin = <26>; scl-pin = <27>; };
In...
Hi,
I have a question about the whitelist，when we use the function "pm_whitelist_set()" to set the whitelist，whether the whitelist is stored in RAM or FLASH? I traced the...
Hello,
I am using nrf52810 with custom board and i have created DFU for uploading a OTA file previously its working fine but i don't know what happens now BLE is getting...
Hi:
When i read data from the device nrf52833 to android app, only get 600byte data and it should be 4096byte. The app use the Android-BLE-Library-2.4.0 lib.
The nrf52833...
Hi,
I have a question on SDK release plans. There is a change awaiting for release (merged after 1.9.1) and it would be nice to develop them with an official release, including...
Hello!
We are two students working on IO-Link Wireless as a bachelor thesis project. Our task is to make a Wireless Master prototype using the nrf52840 DK kit from nordic...
I am making a ble beacon application. I need to send more than 30 bytes of data via advertisement. How can I do? Because UUID data will not be enough for me.
Hello everyone and hello kindly nRF support team!!
One question again sry. I am using SDK 1.9.1 through VS Code and working on the nRF Connect SDK Tutorial - Part 2 -...
Here is the main.c file for AES CTR - /examples/crypto/nrf_crypto/aes/aes_ctr example project
'NORDIC SEMICONDUCTORAES&MAC TEST' is the key
Encrypted hex output: "12 DD...
