I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
I'm trying to use nrfutil as part of a script that sets up the toolchain environment automatically using direnv .
For example:
I'd like to know how the bundle ID can...
As subject, NCS 3.0.2, I use demo 'peripheral_power_profiling' to test current on NRF52832 DK board, but the demo cound not run when power on, There is no log output, and...
Hello,
I am exploring power management on the nRF54L15 DK with nRF Connect SDK v2.8.0 (Zephyr v3.7.99) .
My goal is to:
Enter deep sleep / system off mode.
...
I am trying to wake up the NRF54L15-DK from deep sleep using RTC. The device goes into deep sleep but never wakes up. I would like to know if RTC can wake up the micro from...
Hello,
I am trying to run the wifi_scan example but I am getting a BUS FAULT error as seen below. The SDK is v3.1.0, and the SDK Toolchain is also v3.1.0.
1. Going...
i have version 0.9.2 of the nRF54L DK....
i've noticed there is now 1.0.0 documentation....
have there been any HW changes -- use of "production" MCUs, etc....
more...
Hi Team,
We are looking into the new Thingy 91 X and were wondering if it will be able to run the nRF91 Pizza Demo .
I understand the demo was originally created for the...
Hello,
I'm working on Windows 11, with the nRF Connect for VS Code v2025.5.512 extension, with ncs v3.0.2. I'm using the nRF54L15-dk (PCA10156; 0.9.2; 2025.7) development...
citing the following issues
I've been able to implement the 16 Mhz on the SPIM3. However, the incoming data on the MISO is still corrupted. With my oscilloscope I can...
Currently, we are developing our own board with NRF5340-CLAA. It does not have a 32.768kHz crystal oscillator, only an external 32MHz crystal oscillator. We have applied the...
Hello, I need to do some RTT trace logging, but I can’t enable it. I am trying to create minimal example code, and for this purpose I am using the UDP sample. I added these...
Hi,
We have a working firmware that uses LTE-M for network connectivity to connect to NRF Cloud. But upon testing with NB-IoT configuration (CONFIG_LTE_NETWORK_MODE_NBIOT_GPS...
Hello, the time to ask for help has come again... I keep hitting a crash in my BM833 code related to "Illegal use of the EPSR". Code is fairly simple and supposed to be pretty...
Hi,
hi have the same problem related here: https://devzone.nordicsemi.com/f/nordic-q-a/91890/nrf52-reports-two-jlink-cdc-uart-ports
With revision 2, UART show only one...
