dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi forum,
I am worked on nrf52832 using sdk 15.0.0.
How to used RTS and cts for enable HWFC on nrf52832.
Is their any example for HWFC control through RTS and CTS line...
Hi Devzone,
I use Thingy91. On the nrf9160 side, I run mqtt_simple example; on the nrf52840, I run connectivity_bridge with BLE feature.
When I send "900" via nus service...
I want to control two RGB LED strips with I2S with different GPIO. Not able to figure out how to achieve it. While trying to initialize by separate buffers and data handler...
Hi there,
I have successfully programmed the nrf24le1 on the radio module using the nrf6700 (motherboard) through nrfgo studio. I did so by plugging the radio module into...
Hello,
Is the Power Profiler App capable of calculating and outputting the cumulative energy output to the device under test (when in Source meter mode)? I am using the...
Hi!
There is two things confusing to me about taking IQ samples in AoA application.
1. It is clear to me that that the time between switching of antennae (TSWITCHSPACING...
Hello,
I am using the Nordic SDK v1.5.0, the modem firmware is mfw_nrf9160_1.2.3 and the DK for the nRF9160
In our application, we are using AT commands to setup and control...
Hi,
There is a similar case:
High power consumption in sleep mode after using SAADC
But I am using the SAADC driver version 2.0 because the oversampling feature is only...
I have seen multiple posts about the nrf5340 that confuse me. Posts like this one say that the board/chip is not available yet, as of 4 days ago. But after looking through...
Hi,
I am new to the Nordic Semi world, having recently purchased a nRF52840 DK board and a nRF52840 dongle.
I have programmed an Arduino Nano 33 IoT over BLE and when...
We experience a 15-20% rate of dropped advertisements from our nRF52840 device. We have used our own application on our device and the ble_app_att_mtu_throughput application...
I am using an nRF52832 to talk to a Melexis MLX90393 (which supports 400kpbs Fast Mode) via the TWIM interface. I am using the TWI Manager library to schedule transactions...
See the below stack trace using nRF5 SDK 17.0.2, where execution had stopped while entering a critical region during an interrupt event when another log was being processed...
Hello,
I am developing a BLE peripheral with three services:
Device Information Service
Custom service #1 with two characteristics
Custom service #2 with one characteristcs...
