Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
I have a custom board, with nrf5340, nrf7002 on it.
I would like to get the uA levels of power consumption I see other nrf5340 projects talk about (eg here ) when my application...
Is there any characterization for the nPM1304 (or any in the series) with a charging input voltage in the 3.5-4.0 range? I have a ~4V power source, but depending on load it...
Hi,
I'm developing a project that requires to write GPS data to an SD card. I'm using Nordic SD card library.
I'm able to initialize and interact with the SD card only...
Hi there,
I am trying to send large data files via BLE notifications. My setup is nRF5340 development kit sending data to connecting devices (phone, PC).
I have gone through...
System description
I have an nrF54L15 mounted with an external 4 Mbit External flash with FATFS configured
Filesytem config:
# FatFS File system
CONFIG_FILE_SYSTEM...
Hi
About nPM1300
We will use load switch to drive haptic function and its peak current may up to 0.4A~0.5A@25us duration,
I see the spec show the load switch with maximum...
Hi,
I'm running an app on nRF52840 (NCS3.02) based on the BT shell example.
I did the following modifications:
- shell runs on USB-CDC instead of UART
- using NRFX...
While checking the Channel Sounding samples, I came across the concept of Channel Sounding Security Levels . I have a few questions regarding how this is handled in Nordic...
Hi,
I was wondering whether the nrf54H20 can utilise the BLE sniffing firmware used with the nrf52840?
If not, will this firmware be made available in the future and if...
I have a project that was built with SDK and toolchains 1.7.1. This firmware is used in a fielded product. I can't upgrade it to a newer version of the SDK without having...
I am currently using the nRF54L15 DK board along with an external host to develop Channel Sounding functionality. After reviewing related support tickets, I understand that...
I tried updating my project from NCS 3.0.2 to 3.1.0, but it hardfaults at boot. Doesn't log anything to RTT. The warnings/errors at boot in the screenshot can be ignored,...
Hi everyone,
I’m working with the nRF54L05 MCU (SDK v2.9.0) for my application.
From the documentation, I read that in the system_off demo, when using the z_nrf_grtc_wakeup_prepare...
Hello,
I am working on nRF9160 custom board. Since I am reprogramming a lot, this issue is kind of getting on my nerves. Here is the issue:
Usually modem takes couple...
Hello! I purchased some nRF54L15-DK 0_9_3 boards. Recently, I have been conducting relevant tests on the nRF54L15-DK 0_9_3. I want to test the low power consumption performance...
