Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Does LESC is supported in FreeRTOS?
I init BLE modules in FreeRTOS tasks. After LESC is enabled, system returns error in nrf_crypto_rng_init(). Looks like nrf_stack_info_overflowed...
I'm trying to test out some of the BLE examples on the nRF 51 DK and I'm getting some strange results on the nRF Connect app. When I run the heart rate example, everything...
The modem firmware release notes say
> DTLS supports PSK authentication only
and indeed I can only get PSK to work.
I understand you can't give a timeline, but can you...
Hi All,
We are develop a BLE device which using Proximity profile. And we are modifying the nRF-Toolbox android apk to implement our application. We would like to change...
Hello,
I'm working on a project where I would like to use two nRF52810, one as broadcaster and one as observer. The idea is that the broadcaster sends an advertisement in...
Hello,
I have understanding issues with model inheritance and subscription list (and publish address) sharing.
The Mesh Profile Spec 1.0.1 (chapter 4.2.3) states:
"Within...
Hi,
the mesh profile spec 4.2.1, for the composition data page 0 states: "The size of the state shall not exceed the maximum useful access payload size". The maximum payload...
In SDK5, I found 2 examples : a server GATT in Central & a client GATT in Peripheral...
But in my case my device (nrf52840 board) needs to be :
a peripheral : slave...
Is it possible to send and receive data with the thingy91_at_client_2020-04-29_bc7ade8b?
I found, that this is not supported by AT commands, instead socket libraries for...
Hi everyone,
I have created a custom BLE service with a characteristic and I update the custom value after enabling notifications by calling the ble_cus_custom_value_update...
Hello,
I am integrating saadc example to ble_uart in order to receive analog input signals and send them via ble connection to android application. Low power consumption...
Dear Nordic Team,
We are working on connecting an I2C device to an nRF52840 Dongle . The code we are using is one we've been developing for a few weeks with an nRF52840...
Hi,
For BLE softdevice, I am wondering if it is possible to set connection supervision timeout to infinitive, which means the connection will never be considered lost? ...
Is the process of communication between QSPI and Ext. flash same for QSPI and PSRAM? If not, what could be the procedure?
And how can I communicate with 2 PSRAM using single...
Hello, I want to create a device, that can auto-connect to my phone and only my.
I thought to do it by filtering the MAC address.
But as far as I understand iPhone and...
