Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hi,
I am try to configure internal RC (LFCLK) but device hang in "sd_softdevice_enable(&clock_lf_cfg, app_error_fault_handler);" API.
Changed in "sdk_config.h" to enable...
Hi
When we enable the ADC on the nRF9160, we se a considerable rise in current consumption in standby mode, from sub-100 µA to several hundreds of µA (~400 µA). How do we...
Now that most or all of the Nordic nRF5 SDK is covered by the permissive 5-clause Nordic license (as of June 2017: https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog...
Hi
we are working on ble_nus_c multilink implementation and had problems when more than 1 server is connected: we've noticed that data get mixed between servers.
when...
Hello,
I am using nRF52832, SDK_15.3.0, S132 SoftDevice and Segger for flashing the image.
Is there any sample code integrated with HDC2010 Temperature & Humidity...
Hello,
I use a debugger probe (Segger Jlink) with the sdk_config.h setting SEGGER_RTT_MODE_BLOCK_IF_FIFO_FULL.
When my probe is not connected, there my product is blocked...
Hi, I am new to Nordic BLE development and trying to create an application that has beacon functionality with firmware upgrade over the BLE with the mobile phone and Nordic...
Hi,
So I've been developing just fine on the latest V1.0.0 SDK and SES 4.18. I literally stopped and started a new debugging session and suddenly SES is trying to reflash...
Hello!
I have 3 NRF52840 Preview DK's with Q1AAAA revision ICs. I have been putting those to good use, but I want to test some stuff with SPIM at 32Mhz, which I understand...
Hi,
I am using nRF9160DK, nrf v0.4.0, zephyr v1.14.99-ncs1
I have been trying to measure the boot time from when I press the reset to when it gets to the start of the...
Dear All,
I am trying to enable brown out detection to my NRF9160. From what I see in the data-sheet there is a register that you can set the brownout threshold, but there...
Hi,
looking at the ifx_optiga_custom_example in the nRF5_SDK_15.3.0, i see that for the Hashing calculation the oberon backend is used instead the optiga backend, Why? Is...
Hi,
I see your web: https://www.nordicsemi.com/Software-and-Tools/Development-Tools/nRF-Sniffer#infotabs
There are 4 hardware (DK x 3, Dongle x 1) we can choose to used...
Hi,
I am using nRF52832 with sdk15.3 SES
I need to use DFU.
Buttonless DFU
need to program the controller without the wire connection.
Can you explain how DFU works...
