dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Does Nordic Thingy come with on board SEGGER J-Link programmer / debugger like the nRF52832 DK?
If not then how to program and debug development firmware on Nordic Thingy...
Heloo, I'm using NRF 51 DK and NRF 51 822 QFAA__ mcu.
Flashing the DK is fine, all of the examples are compiling and running as expected, also the modifications introduced...
Have previously used the QFAB. Are there any settings in the compiler or debugger that need to be different ? - my understanding is that xxAB refers to both.
Understand...
I have my own code for configuring digital IO pins. I'm using the PCA 10040 devKit board. When running in the debugger, on startup, the interrupts on the input pins seemed...
Hi Team, Currently we are working with nrf52832 in one of our project and now we are going through FCC for the same. I am using radio tool code(SDK 15.3) to generate the FCC...
hey
I am using the timeslot API to be able to access the CCM peripheral while using the soft device.
For my application the nrf52dk needs to go into sleep mode and wake...
hi, i want to update firmware by OTA from sdk11.0.0_89a8197 to SDK_15.2, but can not scucess.
i tried follow command to build a zip file.
nrfutil pkg generate --hw-version...
Hello,
Here's my current setup:
I am using the nrf52840 SoC for development, which as I understand, has 2 UART instances available. One instance is being used for a third...
Hi
i am using the nrf52832 dk.
I am trying to combine the ble_app_uart code along with the fds code using ses.
what are the changes i have to make in the config file...
I changed the I2C pins to below, and it not work. so is it possible to reconfigure the I2C pin? what should I do since I already set to 8&9 in the hardware board? const nrf_drv_twi_config_t...
Hi,
Looking for some ground on getting the netowork parameters set for a zigbee device, My intention is to limit the number of scan intervals and the scan time to save power...
I'm planning wireless conference system. This needs some condition as under simultaneously use 5ch of wireless bi-directional connection through whole system. Each wireless...
Hi,
I am using nRF52832 soc to develop my project. with nRF5_SDK_15.3 . SES file
I need to connect both BMI160 accelerometer sensor and AT24C512 EEPROM ic in TWI.
how...
I am trying to update firmware that uses v14 of the nRF5 SDK to firmware that uses v15.3, but I am getting the error "Init command larger than expected.".
I'm wondering...
