Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hello. How can I send binary data (in order to not convert it to ASCII string) over UART?
I have sensor data (obtained over BLE). Every measurement is 13 bytes, sample frequency...
Good day!
Thank you for your consideration of my problem! The system is an nRF52832 utilized as a motor driver of a small 2W high rpm maxon motor. The system performs as...
Hello,
I am trying to evaluate the nRF52 dev kit. The "getting started" HTML documentation has a link for "Setting up the development kit". This links loads "Oops (400)...
Despite all the questions on this forum for how to change PWM frequency on the fly, I found no mention of anyone using "WaveForm" mode. Perhaps it's new? There are also no...
Dear all
I have a service with an UUID. Let's say 11111111-2222-3333-4444-555555555555
I also have two characteristics that belong to this service:
66666666-7777...
I am using an nRF52 DK to build a prototype for a product. The device needs to have a connectable advertisement (as peripheral with multiples connections possible) and at...
Hello, thanks for reviewing this. I am trying to install and run Zephyr on the nRF52840 module that is on-board the nRF91 DK board. I have gone through the setup process and...
I'm doing this:
1. Start a scan, with these parameters:
#define SCAN_INTERVAL 0x00A0 /**< Determines scan interval in units of 0.625 millisecond. */ #define SCAN_WINDOW...
Hi
We are evaluating the nRF52832 for use in a medical application, I have modified the example ble_app_cgms_pca10040 to drive our evaluation hw. We are using the Nordic...
I am trying to interface nRF52-DK (PCA10040) with an external MCU (PIC24FJ128GC010) using UART. When trying out the ble_app_uart example in the SDK version nRF5_SDK_15.2.0_9412b96...
Hello,
Will the new nRF Connect SDK that will replace the SoftDevie let us modify the BLE Link Layer specifications? Will the Nordic BLE LL implementation be open source...
Hi,
I'm using SEGGER Embedded Studio in order to build and flash my applications on nRF52840 DK.
I have observed the following behavior:
I try flash the application...
When should I use nrf_calloc (malloc) instead of static declared variable on nrf52840 chip. I mean it has a huge ram memory for as much static declared variables as I would...
I set sd_app_evt_wait in vPortSuppressTicksAndSleep and got the average current. is 0.7ma, Using Other tool measurement , this demo will suddenly increase to a few dozen mA...
