dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
I want to know is there a quick way to include an all ready example from Nordic nRF5_SDK_15.2.0_9412b96 folder into a mbOS environment example (start )? Like copy some XML...
Hi,
The above pins are connected to test points in the ref schematic but stated as Nordic reserved in the pin description. Should I connect them to test points or can I...
I am wondering whether it is possible to maintain backwards compatibility for BL4 while also taking advantage of the BLE5 LR CODED PHY?
I am guessing I could scan in AUTO_PHY...
Hi,
What are the reasons for the nRF connect app or the nRF Mesh app or even the nRF UART app to connect to an Android phone?
I can see the DK advertising. I can see the...
Hi,
I am using nRF52832, SDK 15. My code is based on the freeRTOS code examples.
I am trying to Run my Task Every 10 ms. I tried to test this by using a counter to print...
Hi,
I have a problem with soft device. My code build well but when i try to compile it on nrf52840, i have below error:
Then i tried to go in boot loader:
Therefore...
Hi, Everyone
I have a product (named "A") developed on sdk12.3 and 52832.
This product has peripheral function and MTU Size is 64.
If I use "nRF Toolbox -> UART" on my smartphone...
Hi,
I'm working on the Mbed-OS USB HAL implementation for the nRF52840. I'm having a bit of difficulty getting the expectations of the USB stack to match up with the event...
Hi,
I completed the getting started guide (Getting Started Assistant app) of the nRF Connect v2.6.1:
I installed the toolchain, the SEGGER Embedded Studio and opened a...
Hello I am working through my project and ran into the roadblock of the nrf52840 not being able to use the 250kbit radio mode.
I tried a few workaround and ended up getting...
Hi,
I am working on the "pin_change_init" example to develop my interrupt based function.
I have added three pins/buttons into it and out of which only are working properly...
I AM AT THE END OF MY SANITY!!!
I have tried everything. SEGGER, Keil, installed J-link like 5 times, Python, nRFgo, nRF Connect for Desktop, nRF5x Command Line Tools...
Hello,
We are using nRF52840 with SES sdk 15.0 version. My other thread is here in that got problem with nrf_cal_set_callback(calendar_updated, test_Interval); this function...
I am trying to use a sensor that needs 9600 baud rate with the nRF52840-DK. I've set the baud rate to 9600 on the sdk_config.h. Would I still be able to see the transmit/receive...
