why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi Nordic expert, I wanna get a profile of 51822 performance cycle count. I found 51822 has no powerful DWT feature as cm3 or cm4, would you share me some feasible methods...
Hi All
I am aware that there are some changes to UV5.12 to do with Device Pack location etc.
I have currently updated my project from the .uvproj to .uvprojx extention...
I was able to setup gazell communication between two devices one as device and other as host using 32 byte payload size in nRf51822 module.
Here in gazell communication is...
We are using the Nordic Semi nRF51822-QFAC on our device for BLE. Since we are developing from scratch I understand we need have FCC testing done. Is there a summary of the...
I'm devloping application on nRf51 for that i'm using... SDK : nRF51_SDK_7.2.0_cf547b5 Tool chain : GNU tools arm Embedded [arm-none-eabi version 4.9.3] Dev Board : PCA10028...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
I had a nRF81522 design that was working at 3.3V and I dropped the voltage to 1.9V. I didn't change anything else, but now I am getting periodic disconnects during interogation...
I have a PCA 10028.
This board uses Two microcomputers.
One is N51422.
Another is microcomputer on which the seal is put(Segger ID:).
What is the role of this microcomputer...
I recently discovered this article ( mbientlab.com/.../) and am trying to understand the data transfer type between the firmware ( ble_app_hrs_s110_pca10028 ) and an iOS device...
Hi,
Currently when I run the HRM demo I end up in the app error handler, unfortunately the error codes don't print to my terminal window. I'm using crossworks, and I was...
Hi,
I am new to using keil uvision. I am creating wearable solution, have enabled battery service indication, RTX support,bsp support, gpio,ble service.
When compiling...
Hello!
I would like to measure RSSI for different channels so as to decide which channel is the least noisy one (and more particularly, which ones are already used). I...
I am trying to choose a BLE device for my upcoming biomedical product design. Any help in comparing these 2 devices will be greatly appreciated.
Things I am concerned about...
Hi,
I am using the nRF51822 with an external chip. The nRF51822 has interrupts which trigger when one of the signals from the external chip goes low. When using BLE and...
