As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
i am trying to interface ultrasonic sensor with nrf9160, but i dont get any examples regarding ultrasonic. so i tried the interrupt method to measure the time of gpio...
nRF52832 Product Specification v1.4 states:
11.3 Writing to user information configuration registers (UICR)
User information configuration registers (UICR...
Hello Nordic team,
I'm currently looking into TLS on nRF52840, I'm using nRF SDK 15.3.0.
I have seend the DTLS example "nRF5v15.3.0\examples\iot\dtls\coap_client" that...
Hello Nordic experts,
I am doing SDK 15.3.0 usbd_hid_composite example and this is where I am: https://devzone.nordicsemi.com/f/nordic-q-a/50447/nrf52840-usbd_hid_composite...
My firmware goes into system off state when idle and wakes on GPIO (button input). I want to display an indication to the user for a fixed duration, so I will modify the bootloader...
Hi,
I'm using nRF51822 chip and SDK 12.3.0 library to develop the software. We want to control the motors with PWM. But since PWM consumes a lot of power, we decided to...
Hello.
For My personal project , i would like to develop a buttonless OTA DFU on my Red Bear Nano V2 (Based on nRF52832 SoC Chip) . Im using the SDK11 and i have folloawed...
I'm trying to add RTT support into the secure BLE bootloader to get debug logs, but after adding the files it's consuming too much flash:
Is there any way to fit RTT support...
Hello,
I tried copying code from twi_sensor example to ble_app_uart and got this error:
Error[Li005]: no definition for "nrf_drv_twi_init" [referenced from W:\MODIFIED_SDK_13...
It takes time for fs_event_handler to be called back after nrf_fstorage_erase is executed. In SDK13.1.0, it didn't take much time, but in SDK15.3.0 takes time to be called...
Hey,
I am using nRF52840-DK and SDK 15.2 and working on 802.15.4. The transmitter is sending beacons at an interval of 2sec. The receiver is scanning the network for beacons...
It seems that the GPS is more inclined to give a fix faster when the trigger defined has type GPS_TRIG_FIX set than if the trigger type is GPS_TRIG_DATA_READY. Is this the...
I am working with a custom board and the nRF52840. I have been able to program various hex files to the Nordic chip on this board using SWD and an official Segger JLink device...
