Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi everybody
I'm designing a new cutomremote based on smart remote v3, As I dont know much about the ANR algorithem of Nordic, so for mics I dont know how should place...
Hi,
I'm trying to migrate a prosjekt in SDK 12.0.0 to SDK 13.0.0 and having trouble with the NRF_LOG_RAW_INFO. Getting a warning = implicit declaration of function 'LOG_INTERNAL_9...
Is it OK to drive GPIO P0_27 (when configured as an input, of course) above the supply voltage provided the input current is limited with a series resistor?
In my application...
I'm attempting to build a binding for the noble ( https://github.com/noble/noble) BLE library. Currently some methods are private by underscore prefix convention.
I'd like...
I used nrf52832 sdk14.2 development, modified on the basis of the ble_app_template project, and ported some of the user code previously in sdk12.3 to sdk14.2. After I open...
Hi,
I want to store some data into flash and need to read before calling gap_params_init() in proxy_server demo.
1) when I am initializing flash manager using flash_manager_init...
Hi I wanted to flash a firmware in a Thingy52, I used Segger embedded studio and NRF52 DK to do that. I used the right cable but after flashing my Thingy52, it doesn't blink...
Hello dev zone !
I shall design a compact hardware solution wich is cost sensitive.
I need to use a NRF52832QFAA, I need to provide a 16mhz clock to a hardware peripheral...
I want to implement the function of long Attribute Value reading and writing in BLEV4.0. How should nrf52832 sdk14.2 implement this function? Is there a routine for reference...
I am trying to create a beacon application based on nrf52810.
I am using the following…
* SDK: 15.2.0
* IDE: Segger Embedded Studio
* Hardware: PCA10040 V1.1.1
...
hi.... i am working on ble_uart in segger ... while i am debugging my program stop at nrf_breakpoint_cond ...
how to enable the logging ... please have a look at pic......
hi...
i merged the ble_uart and twi sensor program in segger 15.2 using nrf52832
i have flashed the program successfully, i am getting fatal error while i am debugging...
Hi Sir
We'd want to make lot of nrf52840 devices, and all devices included open bootloader program,
however, the each device USB SDFU port number are different (COM30...
Hi,
I am usig nRF5_SDK_15.0.0_a53641 and writing a program with keil .
I am tryng to read data from the acceleration sensor( LSM303DLHC ) bu communication with BLENanov2...