If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
Hi all,
I am working on Fantel BT40F which uses nrf 5340 soc. I have finished my breadboard testing phase with the development kit and now I am working on Integrated pcb...
Before adding ubxlib module repo into nrf/west.yml, I can build any project with mcuboot with no problem.
However, I cannot build any project with mcuboot after adding the...
Hi,
I'm stuck in the loop of calibration. This is the error that I get from Putty:
It says that I get a TX error.
This is the code that I have for bno055.h:
This...
I used C:\ncs\v2.6.1\zephyr\drivers\adc as an example for testing adc, the following code has been added to nrf9160dk_nrf9160_ns.overlay
I applied voltage to pins p0.13...
I'm trying to test the RGB led on the thingy53.
Using the sample: C:\ncs\v2.6.0\zephyr\samples\basic\rgb_led which gives errors about the devices error: '__device_dts_ord_DT_N_ALIAS_red_pwm_led_P_pwms_IDX_0_PH_ORD...
Hi,
I am migrating from nRF51 to nRF52810 and I am trying to set Debug because its not working in Keil5.
I use PCA10028 board and I am connecting my beacon to P20 port...
I have a nRF9160DK board that is used for development of a custom nRF9160 board. The hardware designers have assigned GPIO P0.27 to be a general purpose output pin. This pin...
NCS 2.3.0
nrf5340dk_nrf5340_ns -- problem is in non-secure domain for an app built with TFM.
I have this in my nrf5340dk_nrf5340_cpuapp_ns.overlay:
at compile time...
Hi, I'm currently getting familiar with mcuboot and DFU
First of all, thank you very much for the new Academy course that covers DFU!
If I understand correctly, to enter...
I am trying to get MCUBOOT working with project based on the Audio_DK base, where we need to do firmware update over UART/Serial interface.
I have added the following...
I am using nRF5 SDK v17.1.0.
Is it possible to connect a peripheral device by MAC address, and the device is advertising with a different UUID from the central device? ...
I am using LittleFS for an external NAND flash by using the KCONFIG option CONFIG_FILE_SYSTEM_LITTLEFS = y and managing the driver implementation manually. This has worked...
Hello! I am using nRF Connect SDK v2.6.0
I'm doing the firmware that will be applied to the custom device.
This device contains one button, to switch on/off the device...
I could use a little help tracking down a linker undefined reference error. I am using nRF Connect in VS Code
c:/ncs/toolchains/cf2149caf2/opt/zephyr-sdk/arm-zephyr-eabi...
I started a project from an example and see that this constant is defined =n in the prj.conf. I am wondering what effect this define has? I can't find any definition with...
