Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
I would like to hide BLE advertising from normal BLE devices.
And only be able to see such advertising with dedicated scanner.
I was thinking of changing access address...
Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
Hi all! I am attempting to download a file from a web server to an NRF52832 using the Nordic IoT SDK version 9.0. Are there any good reference librarie? I found a few for...
Please help to understand. How to configure nRf24L01 receiver for 4-pipe (pipe 0, pipe 1, pipe 2, pipe 3 ). But most importantly, how to specify the transmitter settings that...
I saw earlier post on this blog and viewed on-line video for LitePoint OTA tester that claims to work with all BLE chipsets. We have multiple designs with different DTM interfaces...
Hello everyone. I have both the two boards now. If I draw a PCB myself and want to use the Debug-out port to debug my PCB, what should I do? Which pin should be connected...
Hi Everone..
I want to know for my project Which Example should i use for BLE mesh which support the OTA
I have nRF52832 DK, and several other custom board which is...
In my program, I want to supress all the Printk() statements conditionaly either from prj.conf or CMakeLists etc ? Or in simple terms, want to supress UART0 consol when required...
This is an old problem
first
what has changed in nrfjprog
# Flash the program flash: $(OUTPUT_DIRECTORY)/nrf51422_xxac.hex @echo Flashing: $< nrfjprog --program $< ...
Hi,
A new version of Segger Embedded Studio is available today: V 5.70a. Can I work with this version with the nRF Connect SDK or do I have to wait for a Nordic Edition...
Can nrf21540 support all Nordic products (rf52832., nrf52840 and nrf52810)? Because nrf52832 and nrf52840 have different differential impedance specifications for the IC end...
Hi,
I want use 3 block flash. each size is 16bytes. My code as below
When I call pstorage_torque_0_clear(). I can get flag change from callback function.
but then...
I would like to use newlibc for access to math functions (logf). However, when I enable newlibc I can't get floats or doubles to print with printf when compiling for the nrf52840dk_nrf52840...
I’m using the nRF5280, accessed using pc-ble-driver (API version 6), with SoftDevice S140
I want to efficiently get the list of services from a device, including the 128...
I am using nrf52832 dev kit and soft device s132. I have use my board as an advertiser.
Like if as i put coin cell battery into the dev kit it should wake up from a system...
Hi All,
Hope you are doing well.
I am using NRF Connect SDK 1.5.0 with NRF9160 DK. I want to use P0.14 (Arduino Header Pin) as output for the RESET of LR1110 (SPI Device...
Hi, my app (nrf9160 ns, on DK 1.0 rev.; ncs 1.6.0 ) needs the port pin P0.14 as digital INput (wired on the arduino header, for a shield!!). But something is blocking it from...
Hi,
I'm writing a decoder for a custom radio protocol and I need to measure the rising and falling edges of a signal with high precision. I'm currently using the COMP peripheral...
Have been trying for hours, and searched through the forums, but no luck yet. Modem firmware doesnt seem to load with the following setup. Downgrading to previous Programmer...
