Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
Is there any point to using deferred logging with the RTT backend?
The way I understand RTT is that it writes the message to a buffer where it is fetched via DAP, skipping...
Hello,
I'm trying to implement runtime power management (SDK 2.9.0), but as soon as I enable the option, the shell and logging on UART0 stop working at startup. The rest...
Today I bought a new NRF-PPK2, but compare with my old NRF-PPK2.
For the old and new PPK2, I use the same DUT.
It can't show the same current with my old one? can you...
Hello, We are developing an application with nRF52810 based on nRF Connect SDK V2.4.1. The application is utilizing the BLE connection, particularly the NUS Service (emulation...
Hi,
In our project, we are planning to use the nRF9160 for both LTE-M and Wi-Fi. Thus, we have connected the nRF9160-DK to the nRF7002-EK in the developing phase as we read...
Greetings developers,
I am using nrf connect sdk 2.7.0 with nrf52811 soc. 1) present situation:
My application sequential in nature and does not have multiple thread...
Hi,
I am failing to build any of the Matter, Thread or Zigbee for nrf52840dk with the following failure.
I successfully build a blinky and bluetooth app, so my tool chain...
I am trying to use fstorage with the sd backend (SDK 14.0.0). My issue is that, after successfully calling nrf_fstorage_write, the callback I registered using
just never...
Hello,
I'm developing a program on a NRF52840 DK in the SEGGER Embedded Studio IDE that outputs a PWM signal when a Bluetooth Mesh GenericOnOff signal is recieved.
I got...
Anyone knows why I'm getting this result? I'm building the application using sysbuild and flashing normally on nrf52840dk. I tried both following all the steps in the lesson...
Hi,
i am trying to create an Indoor Positioning System with the nRF54L15.
Currently i am able to connect 1 initiator to multiple reflectors simultaneously,
When...
i have used same Serial_lte_modem sample code from nordic toolchain 2.6.0 , Enabled shell just by setting config macro
CONFIG_SHELL=y and SLM uart loging is by default...
Hello,
I'm trying to run the NVS example on the NRF9160DK rev 1.1.3 with the on-board MX25R6435F external flash memory.
The sample runs OK as nrf9160dk/nrf9160 but the...
I'm working with the Matter Template example and creating a sensor monitoring device on the nRF52840 platform, and I'm developing on a Windows environment with SDK 2.9.0....
hi support team,
i have one problem for 54l15+7002 in ncs2.9.0
I am afraid that I need your help.
I was porting MQTT demo and PERIPHERAL_UART demo together and want...
