As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi I'm using nRF52 DK to program a BM832 module where I want to run some code to manage FLASH memory. I make run examples on the DK but on BM832 module can't be possible because...
Hello Nordic Community!
I have seen previous posts mentioning that the DFU example was not working with SDK 15.3 ( Getting started blog ). But in my case I was able to...
Hi all,
I am working on a new project and I need to communicate to a sensor using I2C, then save the data on a flash (files visible on windows as mass storage via USB) and...
Hi,
I am developing an application where the device should support both central and peripheral roles at the same time. My devices are connecting to a mobile phone. All the...
Hi, I use the nRF52840-DK together with a secure element (Infineon Trust X) and want to measure current/powerconsumption of this whole setup during certain operations. At...
Hello!
I'm currently trying to run the mqtt_simple sample (latest version of nrf-zephyr) on the nrf9160 DK. Unfortunately it is not working, because getaddrinfo() returns...
Hi,
I am using the nRF Connect SDK to develop software for a nRF5340_PDK focusing on Security and power efficiency. Therefore I wanted to make use of the CryptoCell-312...
Hello,
The release-notes of the Modem Firmware v1.0.0 for the nRF9160 state that there is now "Support for DNS server address setting by application.". However, I cannot...
After updating to nRF9160 mode firmware v1.1.1 there have been several vector catches. I have not updated Zephyr or anything else from the latest version downloaded on 9/24...
Hi,
I have programmed my Nordic Thingy 91 with lte_ble_gateway and seems to work fine. However whenever I increase the connection parameters, the thingy91 fails in the discoverty...
Hello All,
Please share me the link where I can get complete explanation on software part for how to use following wakeup options as stated in datasheet
1]The detect signal...
Hi all,
I have 3 nRF52840 Bluetooth tags and I have used Segger Embedded Studio for programming the nRF52840 for the proximity application. Once I have programmed all the...
Hi,
We are seeing some strange stuff when trying to pass floating point values to a function. When we pass the parameter by value (meaning as an actual floating point number...
Hi!
I'm trying to communicate with modem through UART.
Power supply: Battery connected to VDDH
VDD_nRF: 1.8V
nRF52840 DK connected to modem devkit using wires (about...
I am using example code TWI_sensor. It is the same code i just switch ports and added couple of lines that would power up my sensor. After running it i can't even clk going...
