Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Good day. I can't find the schematic of the EVAL NRF52-DK version 2.0.0. The previous version I used was 1.2.4 where I cut the following welding points for testing.
SB22...
I am able to log information to the flashlog backend. When I use the cli interface "flashlog read" I see my information stored (e.g. "operation took %s seconds to complete...
I am trying to download the NRF UART and Nrf Toolbox service the same ones used in the playstore are different than the one on github. The NRF UART v2.0 is different and doesn...
Hi,
I setup one ble mesh network, and it works good for a while. But I encounted a problem that when I power off the mesh node (note: the voltage drops slowly) and then...
Hello,
I am working on nRF51822-QF-AAFQ chip using SDK 12.3.0 in IAR embedded workbench.
My question is, can I impliment DFU in nrf51822 chip?
If possible suggest Starting...
Hello All,
I am trying to add DFU service in the small example with the custom service.
But is not working, facing issues.
I am working on the nrf52810 board with...
Hi all
I am trying to pair nrf52840 (as a central) with ESP32 (as peripheral).
Now I want to get the service uuid so that i can pass to advertising service in ESP32 code...
When restrating the controller, are there any information stored in memory regarding the paired devices or is this up to each implementation to do this manually.
1. If there...
Please tell me about AFH (Adaptive Frequency Hopping).
SDK：15.3.0 例：ble_app_multirole_lesc DeviceA：EYSHJNZWZ（nRF52832）
In AFH (Adaptive Frequency Hopping), the frequency...
Hi,
I am trying to write my own uart init and irq handler routines by accessing the registers directly as per the data sheet. I also referred to https://devzone.nordicsemi...
By some strange reason the thread with my previous question cant accept any replies (and missing the toolbar that appears on the other threads: "Reply Like More"), so will...
Hello,
I accidentally set my board in boot mode and then lost power, then after power on again, the board seems in a total dumb mode: invisible in Device Manager, LED5...
Hello everyone.
I don't know how to start the program when using Soft device.
In the case of example such as example / peripheral / blinky, if it is executed once from...
on the page
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v16.0.0%2Flib_crypto_backend_micro_ecc.html&anchor=lib_crypto_backend_micro_ecc_install
step...
Hi,
I am working on low power mode with DK to apply optimization to our project.
And I verified DK with ble_uart_app can go down to less than 5uA in system on mode which...
