I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
Hello!
Like several others on here, I’m trying to make a multilink nus central firmware. My Peripheral devices run the ble_app_uart example, and the central device runs...
Hello everybody !
Here I am designing a system with 3 development boards nrf52832, where a card called "central" is connected to the computer by USB and this board will...
Dear Nordic,
I'm developing an application using the NUS service en SPIM peripheral. Both of these work correctly independently. Now I'm trying to start an SPI transaction...
I'm developing IO-Link driver using UARTE peripherial.
Is it possible to get event on end of transmition with EasyDMA Tx. Event ENDTX is fired before all transmited bytes...
Segger embedded studio V4.18 appears to have a bug when it comes to printing to RTT. When I run the exact same firmware on SES V3.40, everything is printed to the debug window...
Whether I could build BLE_MESH network automatically within some BLE devices without provisioner?e.t I feel it is manual to build BLE_MESH network with the help of provis...
Hello,
for my project, I am using the module BT832A (from Fanstel) that implements the nrf52810. I am using the pin P.021 to drive a switch. The problem is that when I set...
Hello. I have a problem getting a position via GPS. My dev board is placed in a good place, but can't get a position after more than 1 hour.
I am using you new SW version...
I have been using using nRF9160 as ble gateway for uploading data from one nRF52832 and its works well. Now I need to connect more than one nRF52832 devices, has anyone tried...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hello all,
I am attempting to develop an application which utilizes a third party library for proprietary sensor calculations. This library requires the use of floating...
Hi DevZone team,
Hope you're doing great today. Just want to confirm if the nRF9160 is ready to operate in Mexico. The LTE Bands needed are B2, B4, B5 and B28. The IFETEL...
Hi,
I use SDK 10 pwm example (examples\peripheral\pwm) to modify the PWM cycle to 10s and duty cycle to 50%.
Code showed as below:
But the PWM cycle seem only around...
I have seen the datasheet of nRF52840 but I can't find that any GPIO pin used as SPIS. It says that you can configure the pin those whose value is written in the PSEL.MOSI...
Hello everyone!
I've tried to run mbedtls crypto functions which are using cc310 hardware implementation and I have partitions overlap issue.
Our main goal is to test...
