Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi, i have an existing product but the firmware has been removed from it. i have tried to use the dfu to replace the firmware but i dont know how to get the chip to the point...
The board has been working well.
Since one day, when I try to connect the board with my laptop using micro usb cable, the led5 starts blinking rapidly and I'm unable to...
Hi,
I'm trying to send and receive data to DATA interface that contains IN and OUT bulk endpoint (usbd_cdc_acm example). I'm using libusb on the PC side. It seems like I...
Hello,
I use PPK to measure the power consumption.
but I always get : Failed to start the PPK.
I have measured it last week and it is work.
and this is nrf connect...
Hi Team,
i am working on nrf51822 customized board, the SDK version is 12.3.0 (soft-device is s130 ) and Developing environment in keil 5.26 (on windows).
i am trying...
github.com/.../nrf52-ble-multi-link-multi-role I modified the code to access the environmental values and motion value
but if one thingy access one value such as temperature...
I develop an Android app which connects to a Nordic chip, and I cannot get the Android app to stop advertising once it connects to the central from the SDK multi link project...
Hi,
On the custom board I'm working on an nRF52832 uses the SPIS port with no CS signal (because of the HW connection with the master side of the bus). Since the internal...
Hi, i am trying to disable a signle GPIOTE channel via the INTENCLR. Here is a simple test case:
void gpiote_set_clr_test(void) { NRF_GPIOTE->INTENSET |= ((1<<3) | (1<<1...
Hello ,
I am working on a project in which two devices(one is central and other is peripheral ) uses Nordic bluetooth controller for connection and data exchange. nrf51822...
Hello!
I have been developing a BLE application on nRF52DK and used the ACN52832 as a module for a custom board for experimenting with BLE. I ordered a custom PCB from...
I am just starting using a Thingy:52 and want to use it with a C# UWP app. So far I have been able to retrieve the service and characteristics UUID's without issue but I am...
SDK 15.0.0 nrf52810 Example: Eddystone Beconing mode - ble_app_eddystone SEGGER Embedded Studio for ARM v4.12
I am using ble_app_eddystone example to advertise data in eddystone...
My development enviorment: SDK 15.0.0 nrf52810 Example: examples\ble_peripheral\ble_app_template\pca10040 e SES IDE
I am running above mentioned example without any changes...
