Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
I would like to hide BLE advertising from normal BLE devices.
And only be able to see such advertising with dedicated scanner.
I was thinking of changing access address...
Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
Hi all! I am attempting to download a file from a web server to an NRF52832 using the Nordic IoT SDK version 9.0. Are there any good reference librarie? I found a few for...
Please help to understand. How to configure nRf24L01 receiver for 4-pipe (pipe 0, pipe 1, pipe 2, pipe 3 ). But most importantly, how to specify the transmitter settings that...
I saw earlier post on this blog and viewed on-line video for LitePoint OTA tester that claims to work with all BLE chipsets. We have multiple designs with different DTM interfaces...
It is not possible to connect to the Peripherial using identity address steps to reproduce 1. connect to peripherial using random mac address 2. bond using random address...
I'm currently working with a BL5340PA module with the external antenna connector. we were wondering what was the RF switch isolation between the two antenna outputs. In other...
Hello,
I am currently working on a project using a custom board with nRF52840 + nRF21540 . I am trying to measure wireless performance using Direct Test Mode (DTM) , but...
Hi, when I use OTBR to commission a matter bulb(52840DK), I found this log:
I: 7371 [DL]CHIPoBLE connection established (ConnId: 0x00, GATT MTU: 247) D: 7448 [DL]Indication...
Hi,
I have been trying to use the radio_test example application to try and accomplish my goal but no success so far. My goal is to be able to compose an advertisement packet...
Hello, we would like to use the 4th reference circuit with the QIAA footprint from the Nordic nRF52840 chip's datasheet. However, in our PCB design, can we change the placement...
Hello,
I'm attempting to write to a ble characteristic but when i call bt_gatt_write, I get BT_ATT_ERR_INVALID_ATTRIBUTE_LEN, I have tried to send the same command using...
Question: I am working with the Ebyte E73-2G4M08S1C module, which is based on the nRF52840 . The module provides D+ and D- lines . Can these lines be used for debugging and...
Hello,
I'm trying to put the nRF54L15DK into System Off mode, using sdk & toolchain version v2.8.0.
The provided example (\samples\nfc\system_off) works on my evaluation...
Hello Team, We are currently building a circuit using nRF52833 QDAA QFN40 ( Configuration 5). We would like to know if there are dedicated pins to be configured for BOOT as...
Hi everyone,
I'm working on a Matter based project on the NRF52840 SoC. Since it's an Iot project project we need to reduce power consumption at it's minium for lifetime...
We're starting new medical research project where we have to send data at rate of around 4Mbps from the sensor array for a distance (omnidirectional) of around 2 meters. The...
Good day,
I am learning how to program NRF52832 chips using the NRF52 DK. I am using Segger embeddded v8.2 for the moment as I have not yet learnt how to use the NRF Connect...
Hi,
We have a project based on NRF52811_xxAA_REV1 running on multiple devices without any problem.
Nordic announced recently newer version of SoC (REV2, aka B0) and since...
