Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
we have a 'long lived' tcp connection w/ regular data sends (1hz of 256 bytes for mqtt publishes) where sendmsg() sometimes returns EAGAIN. when trying again it usually works...
Hi Nordic team,
I am using the nRF52840 HCI USB project as the controller firmware, with a Linux device acting as the Bluetooth host.
My application has multiple BLE connections...
Hi,
I am developing on the nRF5340 and using an external modem and an external GNSS module. I am using SDK version 3.4.0.
To operate the modem, I use `modem_cellular...
Hello, We have some problem with connection to WIFI AP.
On NCS v3.4.0, once our device has associated with a WPA3-Personal AP, it can no longer
associate with a WPA2...
I am designing a board around the nRF52832 (QFN48). According to Table 5 in the product spec, GPIOs P0.22–P0.31 are marked "Low drive, low frequency I/O only" (see §4.3.1...
Hello,
Is modem fw `mfw_nrf9151-ntn_1.0.1` production-ready? Is it safe to have our manufacturer flash that instead of the `mfw_nrf91x1_2.0.4`. We are using the ncs-serial...
I'm trying to understand the npm1300-CAAA V1.1 example for configuration 1. The layout looks like this:
You can easily see that several pins are connected on the right...
According to the nRF52840 Product Specification, I observe only the typical value is specified below ：
ION_RAMON_RTC (System ON, full 256 kB RAM retention, wake on RTC...
Hi nordic
I am using the nRF54L10 and Nordic Zigbee Add-on version 1.3.0
I have probably been raising questions about polling for quite some time,
but I have not...
SUMMARY
A custom board (nRF52832, BLE Central + Peripheral roles simultaneously) reliably hits a hardware watchdog reset (RESETREAS shows WATCHDOG only, never CPU_LOCKUP...
Hello,
I have added DFU capabilities to my NRF54L15 project using:
CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU =y
and
SB_CONFIG_PARTITION_MANAGER =y
SB_CONFIG_BOOTLOADER_MCUBOOT...
Hello DevZone Community,
I wanted to share a unique hardware-in-the-loop implementation using the Power Profiler Kit II (PPK2). While the industry is heavily focused on...
I am designing an FPGA to have a SPI slave port connected to the nRF5340 SPIM4 master running at 32 MHz. But the setup and hold times for this configuration are missing from...
I have an application which is not able to talk with my gas gauge device when the TI EV2400 can. Looking at the waveforms all look the same except for the Zephyr code has...
