Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hi all,
I'm having problem porting some project from Keil to SES since our project use absolute memory location to put some variable that will be share between main application...
Hi,nordics
I failed to find primary service successfully .The sdk version is 10.00 and I reffered to the example is ble_app_uart_c_s120.The pripheral is a gamepad .I can...
Hello there,
I was wondering if there's a known issues page fro SDK 14.0.0 (not alpha).
Issue #1: crypto compile error:
I ran into an issue compiling nrf_crypto.c
...
Hi everyone,
Does anyone have the beginner tutorials about BLE migrated to SDK 14?
I am specially interested in those about services and characteristics:
devzone...
what command did "nRF Connect" do, after I click "YES" ???
Im stranded in this example : “ble_app_alert_notification”
I don't know how to use "nRF Connect"
when I...
Hey Dev Zone!
I'm attempting to flash FW onto the Thingy via the nrf52840 dev board (which includes JLink). I connected P19 header on nrf52840 to P9 on the Thingy. I downloaded...
I am trying to run below 10 uA with code below while GPIO and uart are on. Sleep mode is applied (below 10 uA), and only wakes up when button is pressed (can be higher amps...
I have a micro connected to the PCA10040. I can use flow control with 5=rts, 6=tx, 7=cts, 8=rx.
Are these pins necessary or advisable for hwfc?
thanks,
Richard
Hello,
I'm having problems getting a stable channel from an Android device (LG K8) and the nRF52 development board. It is hard to tell whether which side is causing the...
I think the answer is mostly no. My application is similar to the Gazell sample projects, it does not use Softdevice. What are the steps to make my application to be compatible...
I loaded the bootloader on the device and it always advertises as DfuTarg even after loading a application that simply blinks an LED. It doesn't seem to switch to the application...
Looking to put this into our new consumer product, and working with a CE/FCC lab. They would like pre-qualification documents if any. I just need to know if they exist and...
Hello, I would like to copy ble_app_uart_c example to a seperate folder and work with that independently. I looked into the following thread and changed my include paths....
Hello
We produced and assembled our own board based on nRF52832-QFAA chip.
It works fine but we want to improve the performance. We heard at the past that we can provide...
