For the GPS tracker we are developing with nrf9151, the SIM provider is askign for support for the SIM-TOOLKIT .
Do we have any documentation?
Regards
Vivek
Currently we are exploring the features of BLE mesh to integrate this in upcoming project. In this architecture, we plan to use 2 Provisioner in the mesh and one of the provisioner...
Hi ... have code that outputs I2S in master mode. The slave, a NAU8822 device requires Master Clock Source between 8 and 33MHz.
The 54L MCLK pin is duplicating the BCLK...
Hi,
1.How to modify the transmission power of the example direct_test_mode to 4dBm? 2. Please provide Method 1 and modify it using the CONFIG configuration? 3. Please provide...
Previously, I designed a PCB for the nRF52832 chip using the RFANT3216120A5T antenna ( link ). However, I was only able to achieve a very limited Bluetooth range of around...
Hi, I'm relatively new to Nordic microcontrollers and have recently completed the beginner's course. Sorry in advance if I made an obvious mistake.
I am currently trying...
We are running a nrf54l15 board that uses an NFC T2T tag to encode a URI to open an application. We have noticed that sometimes, the current stays higher (~200 uA) after the...
Hi,
Could you confirm that DeviceID found in FICR of nRF9160 is:
1/ randomly generated (64 bits = 8 bytes)
2/ they are not unique, but already on the chip when it...
Hi,
Greetings!
We have successfully checked DFU application from SDK16.0.0 and it works nicely.
We have used android nRF connect app for firmware updating.
Here we...
We have been supplied with a module that sends SpO2 data but it uses 8bit, plus odd parity. I have seen the many questions on this subject and only pose this question to add...
To be able to have USB communication/interface, do I need to apply 5V to VBUS? Or will 3V on Vdd be enough. I am planning to use coin cell that is max rated for 4.2V so it...
this is my code on DFU function, I copy to the example of experimental_ble_app_buttonless_dfu on SDK12.1. I used nrfgo studio to program s130_nrf51_2.0.1_softdevice , boot_setting...
Hi,
I've been working on Thingy:91 under ncs tag 1.2.0, trying to develop simple application using NVS just to see how it works. Based on the zephyr sample I wrote the following...
Hi:
i have some problem about using ble.
in my application has a loop:
1.use ble adv,and Wait for a while，
2.close ble adv ,and using base radio funciton.(do stop...
Hi
I was able to successfully complete the RF output power measurement using nRF52840 DK with the help of Nordic devzone last time.
Based on successful measurement...
Hi,
I use proprietary service to transmit data between raspberry pi and nRF52840 DK. The example I referred to is below.
C:\nRF5_SDK_16.0.0_98a08e2\examples\ble_peripheral...
On the nRF52840, I know the PPI, and therefore any events/tasks, are synchronized to the 16MHz peripheral clock. Here is the quote from the documentation:
"On each PPI channel...
SDK:SDK15.3.0
Example: ble_app_buttonless_dfu project.
MCU : nrf52810
SD: s112
Hi,i want to know how to reduce the ram consumption on nrf52810 sdk15.3.0 ble_app_buttonless_dfu...
My program loaded to a nRF52840 DK unfortunately adresses ports P1.15 and P1.13.
Now the DK is not reachable for Segger IDE and can not be found as a USB device.
I can...
For the connection (peripheral) tab of the online power profiler, I have a question on why if my TX payload is 216 bytes which fits within the LL PDU size, the payload would...
