We have used zigbee sample for coordinator we did many changes in that like subscribing and sending values in UART when any new device gets added.
but noticed ZB_ZDO_SIGNAL_DEVICE_ANNCE...
Hi there,
I was following the tutorial here https://academy.nordicsemi.com/courses/nrf-connect-sdk-intermediate/lessons/lesson-6-analog-to-digital-converter-adc/topic/exercise...
Hi,
I need information about adding an additional flash IC to my project. However, I am wondering if there are any limitations regarding the maximum storage capacity that...
I am testing out the Bluetooth Channel sounding sample with the nRF54L15-dk board using the samples of Channel sounding Initiator with ranging requester. How to change the...
Hi,
we are using the nrf9160 on an addon-pcb as serial LTE-M/NB-IoT modem for our gateway. The host controller is running vanilla Zephyr.
Can someone tell me if I'm wrong...
Hello, I am trying to read the TI ADC1173 at 10-15 MSPS. It has a 8bit parallel interface. I just need to read a very short amount of time, like 5-10 µs (so up to 150 Byte...
Hi,
I am using an nrf5340DK + nrf7002EK. i am able to run an example helloworld application with an immutable bootloader and mcuboot as platform bootloader. When i try to...
Hi,
Last time I met "nRF51822 DK Setup Wizard ended prematurely". The problem was solved by installing .NET framework 3.5 on my PC. Now the same problem is come up "nRFgo...
Now i know the Cortex M0 does not have a floating point unit. Does this mean that we cannot do floating point calculations in our application? or is there a library that will...
Development environment : keil mdk 4.7, nRF51822, SoftDevice 6.0-alpha, nRF51 SDK 4.3
Hello
I develop the application with RF and BLE by receiving UART msg. So, my program...
Section 8.1.2 of the nRF51822 Product Specification states that the "Standby current for 16 MHz crystal oscillator" is 35 uA. The footnote says that the current is drawn ...
Hi,
I met this prompt(see attachements) when I install nRF51 SDK. Who can tell me what's mistake it likes? I have installed microsoft .NET framework 3.5 before in my winXP...
Hi,
i programmed the softdevice with nrfgoStudio but i get an error and i can't load the softdevice on the chip again.
The Error means that the cpu is not halted and that...
Hi guys,
I hope you can answer my question:
I made myself a custom pcb for testing purpose. I can program the nRF51822 just fine. Thats the actual state right now.
...
I have a nRF51822 dev kit, and my dongle is running the master emulator firmware, and master control panel is running on my computer, the dongle is connected and started discovery...
Dear Nordic, could you please comment on your plans to release an over the air bootloader for nRF51822? What is the approximate time frame that we can expect that? Is there...
hi,
I am using nRF51822 chip, I want to added a presentation format to declare a custom characteristic as an array of float (float [3]). According to developer.bluetooth...
I need to program the hex application image into the PCA10001 board. However, if I program the hex file generated by the Keil compiler using nRFStudio, the application does...
Hi,
I'm creating a new service based on the heart rate monitor example, but I'm having some trouble with it.
I implemented my own service, keeping it as similar to the...
when the peripheral and the central are connected,the peripheral will transmit data to the central ,how can i know if the data was transmitted successfully to the central...
Hi,
i want to use the adc, i use the code from here devzone.nordicsemi.com/.../is-there-an-example-code-for-using-pwm-on-the-nrf51822-with-a-softdevice and it works fine...
