Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
Hello,
I´m trying to measure the current consumption on the nRF54L15-DK Rev. 0.9.2.
There are a few questions:
1) What is the role / purpose of the voltage buffer? ...
Hello, I have an issue regarding the current measurement of my nRF7002DK_nRF5340. I am trying to measure the current consumed during the transmission of a carrier on a Wi...
Post:
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the...
I use the security mechanism dtls based on udp communication. Can I implement it on nrf52833? How much flash and ram should be occupied at least? Is there a suggested value...
My eval setup is PPK2(source mode) -> nPM1300EV - -> nRF54L15DK. I have my load connected to BUCK2, everything else is disabled.
I'm getting higher than expected input current...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
So I am trying to figure out what i do and dont have access to as far as flash and ram is concerned. From the nRF51822 spec it discusses this in general but im finding myself...
Hi
My name is Bernard Britton from Trinidad & Tobago and I am looking for someone competent with nRF9E5 to develope a wireless potentiometer position sensor with LCD receiver...
Hi,
While the softdevice is active (nRF51822) available interrupt priorities are:
typedef enum {
NRF_APP_PRIORITY_HIGH = 1,
NRF_APP_PRIORITY_LOW = 3
} nrf_app_irq_priority_t;...
Hi all,
I'm trying to use NRF24L01, using REUSE_TX_PL command,
the data sheet says as long as CE keep high, the chip will transmit the payload continuously, what i wondering...
Hi
Did you have tested the power current of nRF24LU1 when RF was off and USB worked normally?
We want it less than 4mA. Could you have any idea to make it? Thanks.
Hello! I am trying to develop on the nRF51822 eval board as called PCA10001. The programming interface I use is uVision4 on win7.
I would set a static PASSKEY for the pairing...
When I successfully bond with an Android device, then disconnect the Android device, the following attempt to re-connect fails. It appears the chip enters some internal error...
Hi,
after i get eclipse to debug (thanks to cocoa) i need to make a new project. What option i have to choose, to create a new project to run it on my nrf51822 evalboard...
In the nRF51 reference manual, page 59 shows the config value for pullup is 2 (upshift by 2)
In the file nrf51.bitfields.h, at line 2339, we have:
#define GPIO_PIN_CNF_PULL_Pullup...
Hi,
I'd like to add some custom data (25 octets) to the nRF8002 advertisement packets, using the vendor specific data type (FF).
Is this possible in some way or do we...
Hi, I am trying to enabling a notification of an attribute(once the attribute changed, the server will push the new value to the client) and I learned I have to first configure...
What's the proper way to implement bonding that depends on proximity (rather than a whitelist)? So when the client (phone) is close (say, five to ten centimeters) to the server...
I download uart sample from Nordic developer zone . at devzone.nordicsemi.com/.../is-there-a-serial-port-profile-for-ble
Because you had build the uart profile and iOS...
