Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hello,
I could use some guidance on where to look for a power draw that I am not understanding. I am not a hardware engineer but have been tasked with completing firmware...
We experienced an issue in production, in which about 40% of boards had excess current consumption by about 75uA. Root cause was found to be the PIN_CNF of a GPIO pin. During...
Is there any way that a BLE event handler installed with NRF_SDH_BLE_OBSERVER, can stop the execution of other (following) observers?
I have various modules using their...
Hi
I am a student and this is my first project working on BLE. Please keep that in mind.
The end goal is to create a fingerprinting system with a Thingy (nRF6936) as...
I have modified the BLE app Blinky example so that the LED is enabled (state 1) on power up. However, this is not being reflected on the BLE side because when I connect with...
Hi, when debugging, I'm encountering this problem where relevant SPI registers (likely status registers) signaled a successful read before the actual data could be pulled...
We're developing a mobile application which will communicate with a satellite antenna over BLE. We will not have access to the antenna for a few months, and therefore we aquired...
I am using the UART to perform serial DFU on nRF52832. I got it to work fine using nRF Connect SDK 1.8.0.
Now, I need to pass some serial data to the APP when not in DFU...
Hi, I have to develop a new nRF5340/Zephyr/MCUBoot-based device that communicates with a Windows application via USB. The Windows application already manages other legacy...
Hello,
I'm trying to implement a set up of the ble device name from the NVMC UICR register.
But when I try to take it from the register and to set it has a name, it doesn...
Hi,
when using the spi peripheral in slave configuration, what can I expect at power consumption level? does the spi peripheral derive its clock from an internal system...
Hello,
I am using nRF52840 DK's P20 SWD to communicate with an external nRF52840 board . My setup works fine with nrfjprog running from command line. To communicate with...
Is there any example code using a QSPI image as the input for the bootloader instead of e.g. BLE? What format does that have to be in to begin with? Currently doing DFU updates...
Hello friends
I am fresher for Nordic semiconductor . I want to interface triaxial accelerometer of 15MHZ frequency with nrf52840 with inbuilt ADC and transmit the data...
Hello,
I will try to use the macro ZB_ZCL_SET_MODIFY_ATTR_VALUE_CB to define a callback when an attribut is written in my device. But the callback I write is never called...
