Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
Hi,
I have encountered a challenge with the nRF54L15 that I am hoping someone might know a solution for!
My device has a power enable pin (on GPIO1) that must ideally...
Hi
This isn't about a problem so I'm not sure if this is an inappropriate post to make here, if so please feel free to remove it, however there is no commercial incentive...
Hello everyone.
Absolute novice here but a lot of reading over the last few days has brought me here.
I'm currently watching a little robotic project being developed....
The Nordic Hardware Design Guidelines suggest a 0.050 mm soldermask clearance around the pads which should give a 0.100 soldermask sliver between the pads according to the...
Hello all,
Currently I am working on getting the nRF Mesh DFU target and distributor samples working in the context of our project. This appears to have been successful...
Hello,
I have been chasing this problem for some time, but it has been difficult to capture.
The issue occurs when the device is sitting idle (no eDRX or other power-saving...
Hi,
I'm evaluating Wi-Fi NAN (Neighbor Awareness Networking / Wi-Fi Aware) for a project and came across the nRF70 Series, so I wanted to check on the current status and...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Hi
I'm building firmware for the nRF54LM20A running USB HID + ESB at 8 kHz. Currently I am referring to the nRF Desktop ( nrf_desktop ) sample as a reference. But there...
We have thousands of devices live in production and we sometimes encounter the situation that we cannot restart bluetooth advertising anymore after a connection attempt. ...
Hi
We are using the nRF52840-QIAA-R in a lot of PCBA, now I see there is a new revision nRF52840-QIAA-F-R and the old type is not recommended for new design.
What is the...
Hello! Sought out to upgrade from NRF SDK 3.1.1 to 3.4.0 today so downloaded and installed it on Mac using nrfutil sdk-manager command line, and that was fine. The project...
Hi,
In our PCB using the nRF54L15, we used different P2 pins for the sQSPI, believing after reading the docs and driver API, that one could configure different pins than...
Hello Nordic Support Team,
I am testing nRF9151-DK board. I wanted to debug an application that is created when "Create a blank application" option is chosen from nRF Connect...
Hi everyone,
I am trying to use P0.0 but it keeps getting uninitialized when calling nrfx_spim_uninit.
nrfx_spim.c line 659 keeps uninitializing P0.0
It is because...
