Hello,
I am using Bluetooth device "NRF51822_xxAC_s110". My Bluetooth is not advertising when i dump the HEX file to the Bluetooth device which is generated by the Keil Version...
when creating a pairing with a peripheral, the application fails to exhange keys to allow for random private addressing so the peripheral cannot reconnect because the address...
Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
It is a very basic question.
For SOC firmware development with Segger and SDK, which layers of BLE are codes covering? Are Host and controller layers transparent to developers...
Hello,
Due to a routing error, the VBUS pin of the nRF52840 is connected to the GND.
The software works on the devkit but not on my prototype.
From what I saw in...
Hi！
Where master and slave is connecting, and then master is shutdown or move far away.Slave is wait for timeout.But the current of average slave e electric current
...
For my project I need to set the UART0 speed to 9600 baud.
So for testing I tried to compile the "Hello word" example by setting the board configuration file (ncs\v1.6.1...
CONFIGURACION:
NRF52 + SDK15 + SD132 + FREERTOS + NUS.
I have a task sending many packages to a central. I'm having an aboslutly aleatory behaviour: - At some time (could...
I’m checking the transaction of the data between iPhone and a Bluetooth device.
The device is developed by a business partner, but I’m not concerned the FW. I think we have...
Hi,
I am using nRf SDK5 and have a sensor that I am trying to extract the Eddystone UID data from the advertising packet. It shows up in nRfconnect as:
Eddystone UID...
I installed the nrf connect 3.91 with programmer v2.0.1 and J-Link driver v6.88a. However, when I cant seem to see the dev kit on my windows 10. I tried holding the reset...
Hi everyone,
I want to use the RTC module in my code, and I have some questions.
1. What I have understood so far is that the nRF52840 has three RTCs (RTC0, RTC1, RTC2...
Hello,
When using eDRX alone and without DATA (eDRX=81,92 sec, no PSM, no data transmittion,iDRX PDCCH = 1), it's showing an average current of 17,84 uA. This value is similar...
Hi Support team,
I have downloaded nRF5 SDK and found that there is a sample for serial via UART but however the samples ( <SDK Folder>\examples\peripheral\uart) is available...
Hi,
I've designed a product based on nrf52840 soc as a central Bluetooth device. I want to pair and connect to a Bluetooth device (as a slave) that implements a whitelist...
Hello,
When AGPS is activated and trying to fix location, the user see only the final respond once fix is done, but we need to know where the satellites table is stored...
nRF21540
We want to use the nRF21540 FEM to improve BLE range and performance within a building. How does the Tx and Rx amplifier operation coordinate with the BLE SoftDevice...
Hi,
Related to this topic BLE DFU, MCU to MCU (Zephyr), GATT DFU SMP Service Clinet
I would like to know if anyone has any luck in making a SMP client for DFU updates...
