Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Hi, I'm working with nRF52832 DK, SDK 15 on Windows with Keil5. I create Multiperiherial Nus with peer manager and fstorage and it works, but after some connetions I get an...
<error> app: ERROR 8 [NRF_ERROR_INVALID_STATE] at the same line as
ret_code = ble_advertising_advdata_update(&m_advertising, &new_data, true); APP_ERROR_CHECK(ret_code);...
Hi, maybe it's time for my dream project to come true. I have one NRF52840 DK on the table, one desktop PC, one laptop (BT 5), one iPhone X (not mine, just for a case) and...
Hey,
I am new to this , i am using nrf51822 for development , as the documentation says i downloaded the sdk and i got the nrf5 dk and i am using the Segger embedded studio...
Having problems with nrfjprog and a custom board. I connected my custom board to the NDK via P20 and flashed a program to it. The program was a variant of the pwm_library...
dear
i am using this project as slave
\nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_uart\
this project as central
\nRF5_SDK_14.2.0_17b948a\examples\ble_central...
Hello all,
Almost giving up, I'm struggling to make my nRF9160 working. I can't use the LTE Monitor at all!
Tried everything, I think, and run out of ideas. All AT commands...
I have a custom board with nrf52840 with cr2477 battery (1Ah capacity). I was download firmware to board and after a week the battery voltage dropped to critical. In the firmware...
Hello everyone.
There have a scenario, nrf52832 starts a direct advertising , but the dest ble device is not bonded(it could be any other central device), when the dest...
Hi. I am developing the nRF52832 using the NRFX module of the SDK version 15.2.0. We convert the UART signal to RS485 and communicate with RS485 to the outside. RS485 communication...
Hi,
I'm using nRF52832 on a custom board and I have tried to run sdk example nfc_url_record, but it doesn't work.
I have tried to find solution among existing answers...
Hi All,
For my project I'm using NRF52832 IC and NRFsdk. I need 2 GPIO external interrupt to get notified. I'm able to configure both pins and able to see the trigger when...
Hello Dev-Community, I have modified the Thingy Firmware for a custom made board which has also the MPU9250 with TWI connected. Everything works fine, if i use RTT Viewer...
Hi,
Referring to this thread -
If the saadc sampling is trigger by a timer (through ppi), what is the correct way to saadc_uninit() without using the global m_sampling...
Hello,
nRF52832 datasheet denotes saadc sampling time in scan mode (paragraph 37.5.4) as:
What is extra time it takes for the easyDMA to store the samples in RAM ? ...
