Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
So we have our own bootloader project, was trying to get this to work in Segger Studio v6.34 Mac OS Apple Silicon and it would always fail to boot the DfuTarg, the BT would...
Getting linker error "undefined reference to `nRFInitialize'"
Any help would be appreciated, thank you.
T he file 'ses_startup_nrf_common.s' included in project .
Contains...
Hi All!
I tested the central & peripheral_hr_coded examples.By using Nrf connect sdk version 2.0.0 /2.0.2 ,nrf52833DK's. Is it possible to add a feature in the example that...
I am working on implementing a BLE_GAP_ADV_TYPE_EXTENDED_NONCONNECTABLE_NONSCANNABLE_UNDIRECTED advertising setup.
I would like to minimize the current spike transients...
Hi Team We are working on NFC for our new product. When we measure the power level each GPIO we don't reach more than 700mv. Changing the antenna to a larger antenna did not...
Hello,
I have enabled NRF_LOG over RTT but I get flooded by the same message until my application crashed.
For example:
I get continuously:
what am I doing...
Hello List,
First some context: I am working with SDK 17.1.0 on a nrf52840 (arduino nano ble).
Created a variant of the ble_app_uart example and want to add pairing/bonding...
Hi,
I am aware, that I the PDK is deprecated and I plan to use a nRF5340-DK in the near future.
However, I would like to make use of the PDK I have sitting around and...
Dear Mate,
I am trying to build and flash a program by using (+) Add DFU support to your application - Software - nRF Connect SDK guides - Nordic DevZone (nordicsemi.com...
Dear all,
I'm using nRF52832 and using timers to turn on/off GPIOs.
I saw that timer0, 1 and 2 has 4 CC registers.
Right now, I'm using timer0 like this:
1) turn...
Hi team,
I have some doubts regarding mcuboot behavior on firmware failure.
1) Consider the situation I have flashed a new image , it will get validate before mcuboot...
Hi,
I'm trying to use XIP on our custom board running a nrf5340 with a different Flash memory than the one on the nrf5340-devkit.
The XIP worked on nrf5340dk, but now...
Hi,
I have an nRF9160 device which is going thru PTCRB cert. We are doing TRP/TIS and nRF9160 won't connect to the Anritsu MT8821C. Basically it tries to connect and just...
I have a working MQTT subscription list, when I add a new topic for subscription my subscribe fails with ENOMEM error -12.
If I remove another topic, I can add new topics...
I am looking for a way to set the TX power in Openthtread using Matter with the current version of the nRF-SDK. It appears I cannot find a solution which is up to date.
