Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
Hi Team,
Is there any blog/tutorial on how to add custom profile (service/characteristics) with ncsv.1.8.0 and nrf52832/33?
I could find a couple of blogs but they were...
Hello everyone, I'm testing the example ble peripheral "UART/Serial Port Emulation over BLE" with SoftDevice S112 nRF5 SDK v17.1.0 . My board is MBN52832DK and i'm using the...
Hi,
in my project I use the nRF52840 microcontroller as the master I2C device.
Sometimes the TWI peripheral SDA line is forced to a low value by the slave device. This...
Hi, I'm developing an application using fds. I merged fds into ble_app_uart and built complete But when program run fds_init() nRF was crashed I called fds_registered before...
I am using NCS 1.7.0 and latest nRF5340 DK
I am trying to update netcore firmware using the process defined here: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/1...
Hi everyone!
I have a question regarding the audio support on the nRF52833 chip. Is there any support for sending audio ( Low quality compressed audio ) to headset? Or...
Hi everybody.
For a personal project, I need to integrate a flash or a microSD card to store data.
As computation core I want to use nRF52811, but I'm not able to find...
Hi,
I've lost hours to this so grateful for your support!
I have a custom board using Raytac MDBT42Q, which has a 32MHz clock in the module and I'm not using an external...
To whom it ma concern,
we observed Unkwon Resets after Long runtime ; Several Hours.
We use the NRF52840.
After the reset bit 1 in RESETREAS is detected .
BUT investigation...
My project is based on 'ble_app_uart' and I added dfu service..
so there's two custom 128bit uuid in my project..
But before this, I only want to test dfu service mode...
Hi,
We have made an app that gathers GPS coordinates using an external antenna with the thingy91. The problem we have is that we struggle to test the code when we don't...
Hello,
I am using the nRF52840 dongle with the nrf sniffer 4.1 firmware running on it, using Wireshark to read out its results.
This works fine for advertisement packets...
Hi!
In my application, I am receiving A-GPS data from nRF Cloud. After the data is received there is a considerable amount of time where the GNSS module is blocked because...
Hi,
I am looking into the example of SAADC and sending data through BLE. My tests are based on this example: github.com/.../ble_app_uart__saadc_timer_driven__scan_mode...
Hello,
I have been working on a project that uses nrf52832 custom board. Recently, I have been trying to implement device bonding and realized that the data transfer rate...
