Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi Nordic,
We have a reproducible bus fault in nrf_modem_dect_phy_tx_harq() on nRF9151 that we believe originates in the modem library rather than in our application, and...
Hello Nordic Semiconductor Team,
I would like to clarify a component change in our Bluetooth device design.
In our previous product, we used the nRF52840-QIAA-R component...
Background
I had a question regarding Debug Interface mode and its relationship to entering true system off mode versus emulated system off mode (ie WFE in a while(1))....
Hello Nordic Support Team,
I'm developing a BLE audio/walkie-talkie application on an nRF54L15 DK using Zephyr, communicating with an Android smartphone. I'm seeing a significant...
Hi everyone,
I'm quite new to the Nrf Connect SDK and Zephyr.
I'm trying to implement a simple DFU (over UART) bootloader. The idea is that when the microcontroller powers...
Hi,
I have encountered a challenge with the nRF54L15 that I am hoping someone might know a solution for!
My device has a power enable pin (on GPIO1) that must ideally...
Hi
This isn't about a problem so I'm not sure if this is an inappropriate post to make here, if so please feel free to remove it, however there is no commercial incentive...
Hello everyone.
Absolute novice here but a lot of reading over the last few days has brought me here.
I'm currently watching a little robotic project being developed....
The Nordic Hardware Design Guidelines suggest a 0.050 mm soldermask clearance around the pads which should give a 0.100 soldermask sliver between the pads according to the...
Hello all,
Currently I am working on getting the nRF Mesh DFU target and distributor samples working in the context of our project. This appears to have been successful...
Hello,
I have been chasing this problem for some time, but it has been difficult to capture.
The issue occurs when the device is sitting idle (no eDRX or other power-saving...
Hi,
I'm evaluating Wi-Fi NAN (Neighbor Awareness Networking / Wi-Fi Aware) for a project and came across the nRF70 Series, so I wanted to check on the current status and...
Hi all,
I'm working on a Nordic-based system involving multiple nRF52-series chips exchanging high-rate sensor data over both radio and SPI links. The setup involves two...
Hi
I'm building firmware for the nRF54LM20A running USB HID + ESB at 8 kHz. Currently I am referring to the nRF Desktop ( nrf_desktop ) sample as a reference. But there...
