i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hi,
do the AES CCM module, AES ECB module, and the Cryptocell 310 (in nRF52840) employ measures against side channel attacks? I am mainly concerned with timing analysis...
Hi all,
I'm working with nRF52840 PDK and I'm using the last SDK and SoftDevice version: SDK v15.2.0 and SoftDevice v6.1.
I'm using the scanning module introduced in this...
hi
I am using nRF52832.i have added 3 service and and 3 characterastics to one service
1.Peripheral service (accelormeter + gyroscope sensor) and 3 characterstics
2...
Hi, Nordic team. I'm planning to create an iOS 11 BLE app.
I want to create a BLE app that can approximately depict indoor locations after the iOS device scans BLE beacons...
Hello,
I am thinking of using Thingy52 for my project. Before I order Thingy52, I would like to make sure if it will workout for my project.
(1) I wonder if data collected...
I am experimenting with light_switch server example from mesh SDK 2.1.1 . I want to add UART functionality to this example.
I referred to the ble_app_uart example from sdk15...
after cmake -G Ninja ..
-- SDK_ROOT=C:/BLE/SDK/nrf5_SDK_for_Mesh_v2.2.0_src/../nRF5_SDK_15.0.0_a53641a --- set with command line ARG -- PC-Lint executable not found. Linting...
Hi ~ SDK: nrf5_SDK_for_Mesh_v2_0_1 's ligth switch proxy client & proxy server IDEs : SEGGER Embedded Studio for ARM Release 3.40 Build 2018052200.36079 Windows x64 SoftDevices...
I'm looking for the nRF5x SDK v14.2.0-SR3 tha is written on the Smart Remote 3 for nRF52 user's manual. I could not find it on the DevZone, https://developer.nordicsemi.com...
Hi,
I am developing software supporting LEsecure using SDK 12.3 with nRF 51822.
Please tell me what to do when incorrect data is entered in "Passkey entry".
Currently...
Hi.
I've been trying to send a payload with STM32F but I can not. I've used both STM32F103 and STM32F3 to send a payload but neither of them worked. However, when I use...
Hi,
I use nRF5 SDK v15.0.0. In my application I need periodically disable and enable Bluetooth because they are wifi also, which connected to the same antenna. Its mean...
Hi,
I'm trying send me the mac address of the device by UART by the following method:
By serial I receive:
Start b9:24:82:d5:4f:81
The problem its that the device...
Good day
Firstly, an overview.
I am currently busy with a technical proposal for a client. Initial details will result in a completed approx 60 000+ sensor network. My...
Hi EveryBody!
I've begin to work with the n51 family, my board is based on a n51822QFAA H1 IC.
I use Keil5 MDK and a ST-Link V2 programmer. They work fine as I've tested...
