Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
I am contacting you today because I recently bought an nRF5340 development kit, as well as several Nordic Thingy devices (52, 53 and 91) and I have been working on...
Hi, I was reading through the errata for SoftReset and see a note: [161] RESET: Network core is not fully reset after Force-OFF
Can you please clarify how to reset both...
I'm trying to use Adafruit LSM6DSOX (I think it's a misprint and it's actually LSM6DSO), regardless. I can get it to work using I2C but I need it over SPI.
I have been racking...
Hi,
I am working on a board combination of nrf52840 and HL7800 modem. So, I just migrated from 3.6.0 zephyr to 3.7.0 and ncs 2.7-branch.
modem driver: https://github.com...
Hello, I need to scan the advertising data of my peripheral wich advertise with extended advertsing and LE coded PHY.
I use zephyr 3.7, and I work if I use the BLE controller...
Using Modem FW 1.3.6. Using NCS 2.6.0.
We're experiencing an issue in a test setup where we are getting this error reported (528) when trying to clear/set root certificates...
Hello nRF Team,
I am developing a ble terminal app based on the Bluetooth: Peripheral UART sample (nRF Connect SDKv2.7.0) on nRF52840DK. I was testing the app BLE pairing...
When following the unit test example, and even with an alternate minimal implementation, I get the following error:
PS {nRF Connect terminal} > west build -b nrf52840dk...
To people who might be interested in this ticket
I'm trying to make a WiFi connection using the nRF7002 chip. It is a custom board based on STM32 chip. My question is, is...
example:ble_app_uart+ esb_timeslot SDK17.1 Hi Recently our product (PRX) received poor esb communication. I caught through sniffer that when PTX sends a message, our device...
Hi, I have gone through Lesson 4 in Wifi fundamentals. But exercise 1 fails to compile. I have also tested to compile the solution-project, but with the same result. There...
When I look at eh graphic .overlay, I see that the UART0 is there, but no node is assigned. Is there a Node for a two wire UART Driver with no flow control? Peripheral only...
Hello,
I bought a new USB keyboard and since i can't detect anymore Nordic Devboard as nRF5380. No device detected on Visual Studio Code, and on nRFProgrammer neither. ...
Hi,
I working on a project where i measure the distance between nrf52840 dongle and nrf52840 dk using multi carrier phase difference method.
Now, i want to display the...
Hello.
I'm currently trying to send AT Command using an external MCU or USB to UART to check LTE on the NRF9160. The board I use is the nRF9160DK. I changed the pins of...
