Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hi, I am developing firmware for a project using a custom board with the nrf52832. The project requires mcuboot and secure BT OTA. When I enable the configs
CONFIG_BOOTLOADER_MCUBOOT...
Hi,
I'm trying to send gyro and acceleration values continuously using MPU6050(IMU) sensor through BLE after BLE connection is made with other device.
I took ble_app_uart...
I have a few questions regarding the power consumption calculation of the network and application cores from the 5340:
With the assumption that all peripherals are turned...
I am attempting to build a project off of the XXX template repository. So far I have gotten the workspace set up and am now attempting to run "west build" but I get the below...
Dear Support Team,
I just started evaluating a nRF52833 DK board with the nRF Connect SDK 2.3.0. At this point I would like to start playing with the SPI but unfortunately...
Hello.
I am developing device using nRF52840 and i have question about input voltage.
Circuit is converting remaining voltage of battery using nRF52840 (Pin P0.02 AIN0...
I'm using nrfSDK17 with 52832.
When I build my code ,I will get error ad follow:
As L6407E explain,It seem that I only need to scale up IRAM size no less than 0x58....
Hi,
There is one board level hardware change in our new board design that requires different GPIO behavior.
Is there a way to program board revision number in ROM (not...
Hi all! As a disclaimer; I am a beginner with the Nordic SDK, so my understanding may be wrong. Please feel free to correct any holes in my theory. I am trying to use a custom...
Hi. I'm using nRF Connect SDK 2.6.1. I'm developing my own board based on nRF52840 SoC. So, I created an overlay file from nRF52840dk device tree. I could configure and implement...
Restarting the circuit will run the program, and not restarting will not run the program.
I used SES to develop before, and the program would run automatically after downloading...
Hello everyone,
Currently we're working on improving our DALI driver on the nRF52840 chip and NCS2.6.0, because we've experienced issues with transmitting DALI bits with...
Hi,
as a beginner in nrf world I plan to design a mini devkit with 9161. I plan SW pins connector for it to program/debug via Segger j-link and additional UART-USB interface...
Hello,
I am creating a new project that uses the nRF52810 as my controller, and during the development stage, I am using the PCA10040 nRF52832 development board. (I read...
I have three nrf5340 board. Now i want to use one as bis-headset and two as bis-gateway. I want to get two audio from two bis-gateway at the same time. Can i do it? How ?...
