Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
Good day
I have a custom board using an nrf9160 device. On the board I am running a variation of a lwm2m client. I have a question regarding a network connection. Why is...
Hello,
could someone point me where I can find the most current / state of the art example for the BLE UART app for the nRF25840 Dongle?
The version in the nRF5_SDK...
Hi,
I am working on a project which has external flash (FM25V01A ) connected to nrf52832 board over SPI. And when building the project, I am getting the following error...
Hello,
we run an application on a custom board with nRF52840 powered by an external power supply and buffered by a supercap. The supercap then provides the energy for the...
Hi,
I have 2 nrf52840-preview dk board. All of a sudden both the devices are not working any more.
I have referred to some suggestions and tried all the below cases and...
Hi!
Absolute beginner here. I'm trying to use npm1300 (using the evaluation kit for now) with an RP2040 microcontroller (also using RPi Pico dev board). I am powering RP2040...
Currently, I'm using nRF5340 Audio on a homemade board, and I've managed to get the sound input from the gateway as a LINE input and the sound coming out of the headset, but...
Hello ,
I am trying to program external custom board through another nrf52dk via SWD interface to check if external programming method works. The connections between two...
We are using BLE and QSPI at the same time and want to have maximum RF range. Sensor data is collected, encoded, and written into flash via QSPI. This goes on for a few minutes...
I have a question: Is it possible to use BLE Long Range mode (Coded PHY) in the NRF52840 with mobile phones? If not, is there a solution to use it in parallel with normal...
I am using NRF52840's NFC with apple wallet but it requires certification from Apple to be used as tag reader. How can I get it certified so that I can read data from apple...
Hello,
I need to be able to send/receive binary data over this BLE UART Service (bt_nus) on macOS. I'm using the peripheral_uart sample project with no success. It seems...
https://github.com/zephyrproject-rtos/zephyr/blob/main/samples/drivers/spi_flash/src/main.c#L36 may I know where I can find the pin connections used in this example
"const...
Hello all,
We're on the initial stages of a design that requires Wifi (ideally) in a very challenging environment, where in the worst case scenario the temperature could...
Hello,
We have an NCS v2.2.0 nRF5340 application with MCUboot that requires GPIO control of a few pins extremely early in the startup process. We have a signal "A" pulled...
