I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Dear person in charge.
Before using PPK2 for a evaluation of current consumption, I checkd power supply vs corrent measurement by using PPK2 and 5kΩ chip resistor.
I...
Dear All,
I am building an application that needs to use NB-IOT and if that is not available then use LTE-M. I tried sending this AT Command:
AT%XSYSTEMMODE=1,1,0,2
...
When building the Matter Light Bulb sample application for the nRF52840 fails with:
/opt/nordic/ncs/toolchains/v2.1.0/opt/zephyr-sdk/arm-zephyr-eabi/bin/../lib/gcc/arm...
What is meaning of error code 0x3004?
The following is source code of calling sd_ble_gap_tx_power_set().
int _gapTxPowerSet(const int8_t txPwr) { ret_code_t errCode;...
How do we read/write the preferred carrier lists on the SIM card with the nRF9160? Most modems provide the at+cpol command but this doesn't seem to be implemented on the ...
Hi,
We have an application where I'm trying to maximise BLE data throughput to it's absolute highest I can get. Through reading docs/researching and doing some experiments...
1. Is it possible to set MAC address from random to static for Mesh in nRF Connect SDK?
CONFIG_BT_PRIVACY =n and CONFIG_BT_SETTINGS =y seems does not change the behavior...
Hi,
I'm trying to use LPUART in interrupt mode (not async), but I can't get it to work.
I'm using the sample in NCS, which works when using async.
When I uncomment the...
I updated to the latest Toolchain Manager (v1.1.3) and noticed that I am no longer able to select "Open Terminal" to open a terminal window. This was working fine before I...
hello Nordic
i work with ncs 1.7.1, with nrf52832 soc
i tried to add a driver and for some reason i fail and i can not understand why
this is my dts
this is...
Hi,
we use the NRF52840 as a connectivity chip in a serialized application (based on nRF5-SDK v17.1.0 and SoftDevice S140).
When our main app starts, we would like to...
Hello,
While using the at_client sample, when the SMS is received, the following notification is seen
How can I have the access to these notification in other application...
Hi all,
I was recently asked about using L2CAP Connection-Oriented Channel (CoC) to increase thru-put of a project. This must be a gap in my knowledge as L2CAP was always...
Hello,
I've a query.
I am trying to build and see output of " Power Management Example".
C:\nrf_sdk52\DeviceDownload\nRF5_SDK_17.1.0_ddde560\nRF5_SDK_17.1.0_ddde560...
Hi! We are trying to send an HTTP request to our AWS Web Server. The problem that we are figuring out now is that we don't know the way to add a body to our request. We based...
