Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
Hello Nordic team,
I'm developing a proprietary radio protocol and I'm using CCM peripheral for on-the-fly encryption. The packets seem to be correctly encrypted and decrypted...
Hi, I use nRF52840, with SDK 15.3.0
Using UART communication, stored data should be unsigned integer 16 bit.
And the data should be calculated to float data type.
...
Hello there. I am wondering if PWM peripheral in waveform is able to generate a following sequence:
The idea, as you may see, is to generate a sequence with the same Duty...
Hello!
We have hit a wall trying to add support for a particular BLE peripheral to one of our products (which is acting as a BLE central). We support other peripherals,...
Hi Nordic Team,
We have no problem with using ble_app_hids_keyboard app,
However, in some use cases, we would like the application to run as "Just Works" to access other...
Hello everyone,
I'm currently developing a custom firmware for the Nrf52840 usb dongle ( https://www.mouser.de/new/nordic-semiconductor/nordic-nrf52840-usb-dongle ). The...
After power-up and RESET by RESET pin, power consuption of nRF9160 is ~2uA.
After wakeup by WAKEUP pin and AT#XSLEEP=2 power consuption is ~23uA.
What causes increased...
My goal is to use the atmel winc1500 wifi module with the nrf5340. - NRF5340 - NCS V1.9.0/Windows 11 - Atmel winc 1500 I started from the http_client sample (ncs\v1.9.0\zephyr...
Hello, I have soldered up a 51822 and I am trying to connect it with an EmStat pico and get measurements. I am not sure how to program the chip and get it discoverable with...
Hi,
I am using the NRF52840DK and would like to configure the GPIOs to have levels of 1,8V by using zephyr 2.4 or zephyr 3.1. By default I am getting 3 V.
Can anybody...
Hi,
I need help to use FT2232H wit OpenOCD for flashing and showing debug messages from nRF52833 Dev Kit.
Background:
I need to distribute the debug environment to...
Hi there,
We are implementing the %CONEVAL AT cmd in our project and noted that the DL-Pathloss parameter, which is supposed to be the last parameter received, is not being...
I have 3 development kits, two of them work fine with the Audio demo application and one does not: the PLAY/PAUSE button isn't doing anything.
I've probed around the switch...
