Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I might be missing something obvious here, but when the device is flashed (via SES), the application works correctly. When the device is power cycled or reset due to the watch...
I already flash the ble_blinky example to the nrf52840-dongle using nrfconnect desktop. The question is it is possible to do DFU OTA via Bluetooth without nrf52dk or nrfconnect...
Hi,
Can mocks fully compensate for C++ standard features.? Is it recommended to write C++ code in nCS project by using these mocks.? What is the support for C++ operator...
Recently I develop products on nRF5340, I plan to make the full BLE stack run in the net-core, and app-core only runs application. It involves data exchenge between net-core...
Hello,
We have a application with soft device on nrf52832 with SDK 15.3 with 60 uA power consumption. It works as it seems for now.
We wanted to add DFU buttonless feature...
Hi,
We were using Nordic HAL for FEM modules to drive our PA/LNA using nRF52840 on zephyr (no NCS). It was only a basic configuration, where the PA and LNA pins were selected...
Hi.
I have a quick question regarding the RSSI Value of Messages sent in a Bluetoth Mesh Network.
So my question is: How exactly is the RSSI Value defined and how does...
I have a few questions about the DFU:
Is it necessary to flash everything together (Bootloader, DFU, APP) for the initial programming when testing buttonless secure DFU...
If you remove power from the beacon right around the time when the LED is going to start flashing to indicate power on, and do that a number of times you will see it will...
I successfully ran the asset tracker with the 9160DK and am able to receive all data correctly, certificates seem to be working, and everything works as mentioned in the asset...
Hello,
We have a large application using ESB to communicate between many nRF52840 devices. All devices are using firmware with SDK 17.0.2. These devices often switch from...
Hi,
I am using nrf52832 DK.
SDK 17.0.2 softdevice S132.
I am using freertos and running nrf52832 as a peripheral.
I want to put nrf52832 in sleep mode.
I am new...
Hello,
I am migrating code from nrf5_SDK_17.0.2 to nrf connect sdk v1.6.1. The board i am using is nrf52dk(nrf52832) connected with adafruit LSM6DSO.
Everything works...
