Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
I'm trying to add the product key it shows an error "can not the product to your list" and therefore i will not able to access to the User guide
Thank you
hello, im from india im using nrf24l01+ for my project to transmit and receive data between two arduinos. i tried all tutorial basic programs but i cant sucessfully send and...
I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hi everyone, I have a central firmware application connected to 2 peripheral devices: A and B.
I use the method bt_gatt_write_without_response_cb (from zephyr>subsys>bluetooth...
I measured the impedance using a VNA on the J1 socket of the nRF54L15-DK RF: With the RF configured for receive at 78.6 + J7.8, RF transmit continuous carrier at -40dBm: 23...
Hi,
I’m using GD25WB256 as external flash on nRF9151 for MCUboot secondary slot. It’s currently not available from our supplier, so I’m looking for alternatives.
Current...
Hi Nordic support:
Our product used nRF9151 modem. During production, we encountered an issue with approximately 0.1% probability on the nRF9151: It's firmware lost or corruption...
I used the timeslot function of the nrf52832, but when I called the radio to send data, I found that the signal strength was very weak, much lower than that of BLE. This resulted...
I am using nRF9160 DK with nRF Connect SDK v2.9 and the LwM2M client sample ( /samples/cellular/lwm2m_client/ ) , converted from PSK to X.509 certificates .
The device connects...
In the software development for the nRF52832, the SEGGER_RTT_printf() function is called throughout the code for debugging and problem analysis.
Would there be any particular...
Can I copy the ESB code from SDK v3.3.0-preview3 into SDK v2.9.0, and then get the functionality in esb_ptx_ble & esb_prx_ble?
Is there any way to achieve it quickly?
Hi,
I am working on a project with two nRF52840 devices (nRF Connect SDK 3.2.4 / Zephyr RTOS) that are already connected via BLE. On top of the BLE link I need a low-latency...
Hello,
I need to measure current consumption on the nRF52805 in sleep, TX, and RX modes. Which sample applications are recommended for each of these measurements? Additionally...
Hello,
I am facing issue in reading the eDRX mode configurations using AT Commands on nRF9160. Below are the details of hardware & modem fw version.
1. Modem FW version...
What is the recommended way to clear the retained LATCH register using the zephyr generic GPIO functions after waking on interrupt from system OFF? It does not appear to be...
I have designed a custom PCB using nRF54L15 SoC and have gotten it verified from Nordic people. I will share the gerber here as well. I am using VS Code for flashing the code...
# Console disabled - uart30 used exclusively for MCUmgr SMP
CONFIG_SERIAL = y
CONFIG_CONSOLE = y
CONFIG_UART_CONSOLE = y
CONFIG_PRINTK = y
CONFIG_LOG = y
CONFIG_MAIN_STACK_SIZE...
Hi everyone i have a problem with building a project, i dont know what i did wrong, before everything was building fine, but now if i pristine build any project some lines...
