Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hello,
i have read all posts about writing to FLASH when using BLE. But could not find the desirable method.
What i would like to do is to write to flash from characteristic...
Hi guys,
I am using nRF5 SDK for Mesh v4.2.0 and I implemented this simple message model which can enable the communication between LPN and server node. After my nodes are...
Hi everyone, I see in nRF5 SDK 16.0.0, a Button/Led/Timer assign for handler, like that: bsp_init(BSP_INIT_LEDS | BSP_INIT_BUTTONS, bsp_event_handler); Or: app_timer_create...
Hello,
I was working on buttonless dfu feature. I add buttonless dfu service as shown as ble_app_buttonless_dfu example and i manage to perform a ota dfu on nrf52 devkit...
Dear Sir.
Moving to version 2.4.99 from version 1.2.0 .
In previous version SPI worked well , cs was configured in overlay as
&spi3 { status = "okay"; compatible...
Hi,
I was evaluating FOTA on nRF5340 as possible upgrade to 52 series. All went good which I'm happy of.
However application size is limited roughly to half flash size...
Dear Community;
We are trying to send data via Lora using a nRF9160. The Lora transreceiver we are using is a RFM95W(Semtech SX1272). There are samples of code to receive...
Hi all,
I'm trying to set up my nRF52840 Dongle as a BLE Sniffer. I've followed the setup instructions from "nRF Sniffer for Bluetooth LE-- User Guide" v3.2, and I'm using...
Hi DevZone Team,
Is there a way to stop the ZigBee network steering after a device has successfully joined instead of waiting for the timeout to expire?
Thanks
Which nrf5340 BLE examples build and run? I've tried several and get build errors on everything I've tried.
This is for both the app and net processor.
Hi there,
I'm using nrf52840 DK and Custom board, SDK 17.0.2, Segger Embedded Studio(SES v5.20
my problem was the code running fine but after a while it will go...
Hi,
I am using w25q16 serial flash spi memory with nrf52832.
the flash memory is working fine with all analog input pins(2,3,4,5,28,29,30,31).
but due to the hardware...
sdk version:nrf5_SDK_for_Mesh_v5.0.0_src
in example/light_switch
I use the ios nrf mesh app as a provisioner and at the network layer
I can scan and find nrf5x...
SDK 14.2, NRF52840, S140
Hi,
Thank you so much in advance for answering my very long question. I am a little confused by the low power pwm example and app_PWM documentation...
