I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Regarding nRF52840 Dongle, how many Bluetooth devices can it receive? The dongle looks promising and since we are looking for a device that will receive data from 16 handheld...
Hi,
I am using nrf9160DK and ibasis card to test LTE-M signal. I can connect the network using LTE Link monitor as the following figure. But I can't use AT+CCLK? to get...
Hello,
I am trying to test nRF52832DK with standalone environment.
Since now, I am testing with segger embedded studio environment(with debugging)
So, I am now testing...
Hello,
Our project:
At the moment we are developing an application with a nRF52840DK as central and a nRF52DK as peripheral. The code on both boards is based on the ble_app_uart_c...
Dear All,
I have chosen NRF9160 device for two requirements - SMS transmit or receive and LTE IOT connectivity [Both are different project requirements].
After going through...
As I know, nRF52 series is produced in the TSMC on 55 nm ULP process. But I can't find any info about the integrated circuit manufacturing process of nRF53 series. Could you...
Hi, I use a nRF52840 with the nRF Sniffer Firmware for capturing advertisement frames and connections between several devices. My question is if it’s possible to capture communication...
I'm writing custom boot loaders. One of the capabilities is to update the network processor from code running on the application processor. The PCD subsystem looks like it...
On 3/11, we received a message from the Nordic "HomeKit Team", announcing that HomeKit support in now integrated in the latest release (ncs 1.5.0) and distributed through...
chip - nrf52840 sdk - nRF5_SDK_15.3.0_59ac345 softdevice - s140nrf52611
Issue enabling usb cdc without softdevice enable.
The COM port does not show up without the softdevice...
Ring buffer operates on uint8_t , but I would like to use ring buffer to store 16 bits ADC data. What is the simplest solution?
Converting 16 bits data into 8 bits, store...
Hello, Guys!
As I know, the Bootloader uses RTC2.
The problem is that RTC2 continues to operate after executing the bootloader, in my Application.
My Application not...
We are using nRF52840-DK and we need to stream the audio to our iOS app that we are developing. But currently, we are not able to get the audio streams back for mic to iOS...
In my application we have an ADC input pin which we want to connect to comparator input too. Based on the highlighted statement in section 7.6.1 Can the same analog pin be...
Hello,
since a few weeks I have the following problem with the nRF Connect for Desktop app on Linux (Arch Linux specifically). The runner launches and I can install and...
