I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hi,
My custom card has ic nrf52832QFAAE0 AND NRF52DK has ic NRF52832QFAAE1.MESH SDK EXAMPLES runs properly on NRF52DK but not working on my hardware with ic NRF52832QFAAE0...
Hi,
What cellular connectivity, the provider's DNS, and backend cloud services, invariably connecting over MQTT is transient and the internal blocking timeout of mqtt_client_tls_connect...
I'm using Zephyr on a nRF52840 and I'd like to use the QSPI with the Fat Filesystem. I added the following Config statements to prj.conf:
The nrfx QSPI driver and file...
Hello,
I am wondering where to change the baud rate for the UART in the NRFConnect SDK using zephyr. I am working with the peripheral_uart example.
Thanks,
RJ
Hello,
i just migrated from nRF51 to nRF52. I tried to implement my custom service. I followed the tutorial from this site: https://github.com/bjornspockeli/custom_ble_service_example...
Hello,
in our application we have two devices. A nrf52840DK as central and a BMD-300-EVAL (contains a nRF52832 chip) as peripheral. We need a timer/counter that generates...
Hi,
I had used nRF Connect Programmer to flash nRF Sniffer firmware on my nRF52840 Dongle, but after that, when I tried to flash the firmware again, I found that there was...
Hi,
I want to add new peer to peer manager using pm_peer_new().
pm_peer_id_t p1 = 0;
pm_peer_new(&p1,&bond_info,NULL);
there are no peers, so trying to add as peer_id...
Bought 2 nRF5340 DK kits from Mouser. Followed the setup instructions and fell at the first hurdle. Attached NF antenna, connected to USB and switched on.
Nothing. Green...
Hello,
I am currently working on a project that requires data to be sent over Bluetooth. I currently have an NRF52832 Development board and have been trying examples and...
Is there any difference in terms of RF performance between different hardware versions of nRF52840? Can someone point me to the relevant documentation?
Thank you
I am working on the nRF52840 DK board SAADC module with nRF5_SDK_17.0.0 SDK, and I am unable to get the output on RTT.\
I am working on the pre-prepared program from the...
Click DFU after connect. Navigate to folder. Click .zip update file. Click OK. File name does NOT appear in chosen text box, box remains empty. Works correctly on English...
Hi everybody, I'm trying to set up my 52840 DK to scan for BLE_GAP_PHY_CODED advertising packets from 52840 Dongle. I think I was able to program the dongle, because it doesn...
