Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Does the Antenna in this Beacon relates with this "BAL-NRF02D3 '50 ohm balun transformer for 2.45GHz ISM"? Any idea what's this "BAL-NRF02D3" for? many thanks!
I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Hello All,
We have developed a Zigbee End Node device for which we would like to make a radio test.
we are using nRF connect SDK 2.0.0, please note the reason we use the...
Hello Nordic Team,
I’m currently working with the nRF5340-DK and nRF Connect SDK (v2.6) using VS Code . I’ve been testing OTA firmware update processes using MCUboot and...
Hello
I need help, I have a problem implementing ppi gpiote and spim. The ADC I use is mcp3562 which sends via the irq pin when the data is ready. I need to work in continuous...
I used Nordic52480 DK(bulb) as DUT to run Matter Certification case TC-DGGEN-2.1 .
Steps:
1. setup OTBR on Pi4：./certification-tool/backend/test_collections/matter/scripts...
Hello I have an nRF52840 board with a 2 MB external flash I'm using SDK 2.6.2 I'd like to configure the mcuboot_secondary partition to be on the external flash
Here is my...
Windows 11, VSCode, NCS v2.3.0
Hi, I have a well-working application that I would like to build ztests for.
I'm reading about how to do that on the test framework page...
I often see the following warning when requesting a GNSS location: "<wrn> location: PSM is configured, but modem did not enter PSM in 2 minutes. Starting GNSS anyway." - what...
Hi everyone,
We’re currently using the nRF9160 module with JIO Nb-IoT SIMs in our devices. Could anyone clarify if any specific actions are needed in the firmware for...
I have an nRF54l15-PDK dev board (brand new):
I did the following commands with the SDK v3.0.2. Building and Flashing went fine:
to build:
west build -b nrf54l15dk...
During development we noticed that current measurements coming from npm1300 appear to be much higher than expected despite the results not matching what we were seeing on...
Hello, I have a question about the headphone jack output on the nRF5340 Audio DK.
In past DevZone threads, it has been stated that “the headphone output through the CS47L63...
Hello,
With reference to BLE Fundamentals Lesson 4, I am try to modify my existing BLE code to add indication support.
After adding the codes, I can see the "Read and...
We are encountering an issue with flashing firmware to our newly designed nRF54L05 BLE board.
Issue Details:
We are trying to flash a .hex file (simple Blinky code...
