I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
Hi,
Using 'nrf5_SDK_for_Mesh_v5.0.0_src' exampe project 'light_switch' developed for nrf52 Development Kit(pca10040). How to make the same project working on Thingy52(pca20020...
I am working on a project based on the ble_app_hrs_rscs_relay example project which I have largely extended with many additional services.
For example I am offering an additional...
Hi
I am working on nRF52832 , I want to store the data in NVMC . so I am trying to write the data blockwise , I saw the layout each page consists of Block 0-7 .To each block...
Hi everyone,
Is it possible to implement a USB device belonging to the Personal Healthcare class with the nordic nrf52840 DK?
NRF supports Personal Healthcare USB class...
Hi, I have written these 3 functions to erase/read and write. When I write any value from address 1 it gives following wrong output(0 1 2 3). But When I start address from...
Hi nordic team，
I use the nrf52832 EVK ,I want to connect MIC and speaker to the EVK.
I read the nRF52832_PS_v1.4.pdf, and i guess following interfaces can be used.I don...
Hello
I am using Linux PC
nrf52832
chmod 777 to the nordic serial port
using the bt_nus_shell script :
sudo python bt_nus_shell.py --name BT_NUS_shell --com...
I want to use nrf5340 on DTM mode (installed through nrf connect) to test Carrier frequency offset for CTE packets using CMW500. However, CMW uses power trigger to find the...
I have developed a custom PCB based on nRF 9160. I have followed the connections as per the attached image
Can I use Segger Embeded Studio to program the custom PCBs. If...
Hi there!
How i can put nrf52840 NCP module into low power mode or turn it off? By SPINEL_PROP_MCU_POWER_STATE property of Spinel protocol getting error - "Prop_not_found...
Is it possible to implement a wakeup/power-on-long-push?
Working with the pwr_mgmt example from SDK 17, I see how bsp_wakeup_btn_config works to enable a BUTTON_ACTIVE_STATE...
Hi, I have a project in which I need to connect to an infusion pump via BLE.
I need your urgent help :)
The pump is advertising every 15 minutes for 10 seconds.
how...
hi,
Using nrf52840
setting new mac address results Error 12802:
using mac : 7F:37:DA:47:22:B1
gap_addr.addr_type = BLE_GAP_ADDR_TYPE_RANDOM_STATIC; gap_addr.addr_id_peer...
Hi Team,
We have ported the code from SDK 16 to 17.0.0 version. While compiling we are getting error (attached the screenshot).
But the all required files are included...
