Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
I would like to hide BLE advertising from normal BLE devices.
And only be able to see such advertising with dedicated scanner.
I was thinking of changing access address...
Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
Hi all! I am attempting to download a file from a web server to an NRF52832 using the Nordic IoT SDK version 9.0. Are there any good reference librarie? I found a few for...
Please help to understand. How to configure nRf24L01 receiver for 4-pipe (pipe 0, pipe 1, pipe 2, pipe 3 ). But most importantly, how to specify the transmitter settings that...
I'm evaluating possibilities of BLE-LESC Pairing/Bonding with the ble_app_hrs peripheral on the nRF52840-DK with SDK 12.3 and SoftDevice s132. To see what's going on in the...
Is it possible to flash multiple custom boards using sagger DKs at the same time?, assume 2 custom boards and 2 DKs, would they be able to flash the custom boards in parallel...
There are many places in the file fsm.c that have this compile condition check
#if defined FSM_DEBUG
blabla
#endif
that is wrong. The compiler will ignore it. There...
Dear Nordic,
Hello, I have to configure 2 UART. I have saw this post .
however, I have made a demo version for the project without 2 UART function, so I hope to apply...
Hello, I´m trying to compile the BLE Heart Rate service projects using SEGGER Embedded Studio. After importing the project from nrf52 SDK, I tried building the project but...
Hello,
I want to implement home automation project using 3 nRF52840 dongles. i.e I want to connect all the 3 dongles with each other and the signal sent from one device...
Hello, I am trying to design a product based on BLE MESH. I would need gateway to be able to accumulate data from network and send it outside. I need that gateway to connect...
Hi,
I have gone through the "ble_app_hids_mouse" example program. So far the program seems to work great, but how do we take control of the buttons since the function used...
Hello,
We have plan to use nRF52832-CIAA with external antenna connector (MHF4). I noticed that in 4-layer reference design layout there is quite big square keepouts on...
Hi,
I am using sdk 14.2.0.
i am using freeRTOS,created 3 threads.
all are running fine,but just for while(2 - 3 minutes).
after that, all the threads stoped.
may...
Hi,
I am doing OOB commissioning with OpenThread. According to section 10.12 of Thread 1.1.1 specification, Active / Pending Operational Datasets need to be persisted to...
Hello,
I'm trying to connect external RTC, which has a 32kHz clock on it's pin to nRF52832. So far I've had issues with connecting this clock to P0.00 pin and having P0...
Hi all:
when i add uart code in ble_multilink ,and it gived me errors like this:
"<error> app: Fatal error <warning> app: System reset <error> app: Fatal error <warning...
If I put too many characters into a serial using IRQ mode, it stops reading input.
I haven't tried polling or DMA yet.
Using
nRF5_SDK_15.0.0_a53641a
gcc-arm-none...
