I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Hi ,
Could anyone please with NRF9160-SIAA-B1A-R7 CAD Files (symbol, footprint, and 3d file) for KiCad ?
Thank you for your support.
Best regards, Mohamed Obaid
I'm using an nrf52840 on a custom board and send debug messages with printk to RTT. When mcuboot is added to the firmware it is no longer possible to read the messages from...
Hi nordic support Team.
I try to build blinking led example: nRF5_SDK_17.0.2_d674dde\examples\peripheral\blinky\pca10056e Load firmware for NRF52811 and NRF52840, i see...
Hi,Team,
I am developing Long Range and Pawr using nrf54l15-dk.
For the Long Range example I refer to E:\NCS\v2.8.0\nrf\samples\bluetooth\central_and_peripheral_hr and...
We previously used the nRF52832 (with Segger Embedded Studio) and implemented OTA updates for it, along with developing a custom APK.
Now, we are using the nRF5340 (with...
My nRF52840 DK needs to interface with a convential device using the data bus and address bus. The following diagram (P.27) from the nRF52840 PDK user guide.shows the data...
Hi,
I got a question on IQ Sampling with the direction_finding_connectionless_tx/rx example.
Settings:
Sample Spacing = 125 ns
Sample Sapcing (Reference Period...
Hi,
I have an nRF5340 DK, and my BLE project runs fine on it. However, when I flash the same code onto my custom board, bt_enable() returns error -11 , which seems to...
Hi
In the newer versions of nRF Connect for VS Code, the NCS and toolchain version can be configured per build-configuration.
Is it possible to configure the desired versions...
Hi all, will need to post short as I am getting a "cannot create ticket" error.
Hi all,
I'm quite new to nrf, zephyr and embedded of this complexity but have completed...
This is odd, one thread can access i2c API just fine.
Another tread the same API call causes Secure Fault.
(These threads are mutually exclusive btw), the environment...
Hi,
I am trying to get the GPS coordinates from nrf9160 devkit so far I am following this guide . I was successfully able to get the coordinates once using:
However...
I have implemented a ublox ANNA-B402 on a custom board and am trying to flash code using the debug out header (P19). I am using Segger Embedded Studio and am flashing code...
