I'm analyzing app_timer scheduling code..
I have an question about list_insertation_handler function in SWI0_ISR
I think if ( (p_timer->ticks_at_start - m_ticks_latest...
I would like to test the newly added v4.2/v5.0 Bluetooth features (e.g. LE Secure Connections, Data Packet Length Extension, 2xSpeed, etc) against non-nordic devices. I have...
I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
We want to interface the SE050 NXP IC with the NRF5340 using the I2C protocol and generate an AES-256 key.
Could you please assist us in generating the AES-256 key using...
I tested on nrf5_sdk_17.1.0_ddde560，Tested on nrf5_sdk_17.1.0_ddde560\examples\ble_peripheral\ble_app_hrs_freertos project。Call the testfun function to test the test。
The...
Normally when I connected the nPM1300 it would automatically display the battery status and settings,
I already switched up the npm1300 but none ofthem work here.
Is...
Hi
I am working on a project which uses distance measurement config for multiple peripherals with long range.
Our plan is to support DM for up to range 25m and we observed...
I want to achieve time synchronization over a wireless connection with sub-microsecond latency. While PTP (Precision Time Protocol) can provide nanosecond-level accuracy on...
Hi, Nordic Bluetooth Controller Teams, I have a question. I see that the Aux offset of Bluetooth extended broadcast on NCS is fixed at 330us. What is the consideration behind...
Hi,
Is there a Zephyr sample project on QSPI with nRF52840? What I want to do is to write/read to an external flash (W25Q16JVSNIM).
Thank you
Best regards
Dav...
Hello,
I work on a thingy52 since few weeks with a nrf52832 SoC. When i'm turning it on and connecting it to my computer, there is no led turn on and it is not detected...
Im currently working on BLE SMP DFU on Nordic52840DK (Connect SDK v2.7.0) based on this example:
https://github.com/hellesvik-nordic/samples_for_nrf_connect_sdk/tree/main...
Hello everyone,
I am working on a project with a Thingy91 that has an nRF52840 and an nRF9160 , and I am trying to read the battery level. I want to measure this battery...
In ticket Case ID 290251, Torsten Rasmussen provides the following advice to ensure that the toolchain corresponding to the SDK is used to build the SDK (this applies to nrfutil...
I am lab testing Nordic's DECT-NR+ (DECT) for a new factory automation application; I am using the hello_dect sample application from the PHY webinar demo, I am trying to...
I made a custom board, uploaded the Arduino bootloader and was flashing the firmware with Arduino I used it without any problem with revision 2 But when I use revision 3 chip...
Hi! I'm working on the firmware part that needs to perform operations on the same variables both inside GPIO IRQ and the software timer callback. So, there is a need for a...
