Hi. i'm using nRF51822AC, SDK12.2.0, S130 v2.0.1 as central.
I want to make sure that how to operate DFU.
Please check there is missing point or wrong point.
Step 1...
Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi all,
I'm working on a project with an nRF52840 using the nRF Connect SDK (version X.Y.Z) and Zephyr RTOS. My goal is to achieve maximum possible range for non-connectable...
nrf modem: 1.3.4
sdk: 2.3.0
Custom board.
We have an asset tracker that caches events when out of connectivity zone. We can accumulate 10-100 messages depending upon...
Hello!
I have designed a custom board with the nRF5340 , powered at 1.8V. I am able to program the chip successfully, but after the firmware is downloaded (Zephyr RTOS,...
In my application we have an nRF514L configured as an SPI target. Page 830 of the nRF54L datasheet (version 0.8, dated December 2024) documents that the SPIS peripheral requires...
Hi,
We want to enable zephyr shell over RTT on our custom board based on nrf52840. I tried the 'shell_module' sample with prj_minimal_rtt.conf and it works fine on nrf52840...
Hi there,
I built a battery powered custom PCBA with the NRF54L15 and the nPM1300. All the configuration and register work via I2C seems to be working properly (reading...
Hi. I have a working IAR project based on the nrf52 SDK \nordic\examples\ble_peripheral\ble_app_uart. i am attempting to port the project to ARMGCC using VSCode. I am at a...
Hello. I try to create a remote control for GoPro using nrf52 ble.
Using sdk 17.1 examples I can connect to GoPro and try to get a list of UUIDs. But I only get one UUID...
Hello
I'm using the settings partition to store user configuration data. I know that the BLE stack also uses it — particularly for storing bonding information — but I don...
Hi,
I am working on a project with nrf52832 and LIS3DH for a beacon.
I have added the low power feature into my application to go to standby mode in case of inactivity...
Hello Everyone,
I am using a nrf54l15 for my current project and ran into some discrepancies within the documentation provided for the processor.
Even the AI chat bot...
Hey I was working on starting sample code of wifi in ncs v2.6.1. When I added the correct ssid but wrong password in the prj.conf to check the status of the connection failure...
Hi there,
I am currently trying to use device sleep modes with Matter. Nevertheless, once I add "CONFIG_PM_DEVICE_RUNTIME=y" to my prj.conf, the main-method is not longer...
Hi, I have been experimenting with the Direct Test Mode program. I am using an nRF9160 DK, specifically the bluetooth chip nRF52840.
The Direct Test Mode is not officially...
Hi,
I am using sensor observer sample to get the data from sensor sample. However, I notice the power consuption is too high. I have look thourgh the forum and found this...
