Hi,
I'm struggling to get a mouse wheel to work in advanced (High Res) mode.
What I learned so far is that I should create a "Resolution Multiplier" Feature report....
i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
I am trying to use PWM to control two LEDS, one red and one green (referred to as blueled in the code) to produce different colours. I have had a look at the example...
Hello,
When we flash the BLE Zephyr project to the external chip (nRF52833), do we need to add the SoftDevice controller .hex file as well, or does the merged .hex file...
I am trying to send / receive bi-directional audio between two nRF5340 Audio DKs with an external I2S bus on the gateway DK. I am modifying the nrf5340_audio example from...
Hi,
I'm working with nRF5340 and would like to store my own data in the NVM (2 bytes in total).
I couldn't figure out which flash partition is relevant for this and what...
Hi,
I just started developing a BLE Central device on a nRF52840 DK. After successfully connect my DevKit with a phone acting as a peripheral (using nRF Connect Mobile)...
Hi,
There are two 'should' (as opposed to 'must') statements in the Fast Pair implementation guidelines for Locator Tags:
1. The Provider should reject normal Bluetooth...
Dear Nordic Support-Team,
I am trying to documentation on the Device Identity key in the nrf9160. I found something here: https://infocenter.nordicsemi.com/topic/ref_at_commands...
Hello everyone,
I am a college engineering student working on a circuits project, and I need some help. The project is to design a proximity device that sounds an alarm...
SW version :2.4.0 HW revision: nRF52833 development board, PCA20054 Direction Finding Antenna Board 1_0_0 I use the routine director_finding_central and director_finding_periopheral...
My purpose is to create a beacon that communicates acceleration and heart rate values using BLE.
First of all, I tried to merge the nrf52832 SPI and SAADC sample programs...
Hello.
I am developing device using nRF52840 and i have question about IO pin usage.
The circuit is currently providing voltage to the A12 pin (Digital I/O), but it is...
hello
I am studying DFU with reference to the Academy.
Exercise 1 - DFU over UART - Nordic Developer Academy (nordicsemi.com)
SampleCode of Exercise1 use McuBoot and...
Hello,
I want to use McuBoot so I added CONFIG_BOOTLOADER_MCUBOOT =y to prj.conf.
So t here were a lot of warnings "implicit declaration of function ".
Part of the warning...
I need to use 9160 to drive the Lis2dw12 accelerometer for ST. I found some settings related to this accelerometer in NCS, but I couldn't use it after adding it in IIC, and...